answer to DIYspaceW #1541
Hello DIYspaceW,
you are in europe. You can check Conrad Electronic Shop >> Ihr Lieferant fur Elektronik and search for
everlight mv5075c.
In Germany available at a price of ca. 0,69 € per piece.
I think they will deliver to slowenia? But not sure.
And shipping costs will be much higher than the LED - price.
Greets
Dirk
Hello DIYspaceW,
you are in europe. You can check Conrad Electronic Shop >> Ihr Lieferant fur Elektronik and search for
everlight mv5075c.
In Germany available at a price of ca. 0,69 € per piece.
I think they will deliver to slowenia? But not sure.
And shipping costs will be much higher than the LED - price.
Greets
Dirk
Hello guys I need a substitute for the RED LED in MountainView! Mouser doesnt sell it to my country
so please any suggestions?
Please have a look at
posts #201 and #202
post #433
post #554
post #442
and finally
post #461
Hello DIYspaceW,
you are in europe. You can check Conrad Electronic Shop >> Ihr Lieferant fur Elektronik and search for
everlight mv5075c.
In Germany available at a price of ca. 0,69 € per piece.
I think they will deliver to slowenia? But not sure.
And shipping costs will be much higher than the LED - price.
Greets
Dirk
Great Dirk! You right I can order to Slovenia! Danke!
Yes, ships out this weekend. Mouser shopping cart assembled by Vunce just posted in the thread.
A big thanks for all!
Russellc
Is there a way to order a new set of boards?
You can have mine. Send me PM with address and I'll get them to you.
You can have mine. Send me PM with address and I'll get them to you.
Thank you very much.
Can these be used for the voltage ref. Q6 and Q7 ?
LM385Z-1.2/NOPB | LM385Z-1.2/NOPB, Fixed, Spaendingsreference, 1,235 V, +-2.0 %, 20mA, 3 ben, TO-92 | RS Components
I usually get my components from RS and there was not direct hit on LM385_1P2 …...but close…...
LM385Z-1.2/NOPB | LM385Z-1.2/NOPB, Fixed, Spaendingsreference, 1,235 V, +-2.0 %, 20mA, 3 ben, TO-92 | RS Components
I usually get my components from RS and there was not direct hit on LM385_1P2 …...but close…...
Order placed. Thanks for your help.
Skip
JFETs of 10.82 idss
I would like to know also. Hope someone replies !!!
I’m going to build the ISHIKAWA daughter boards and have match JFETs of 10.82 idss. I read somewhere a recommendation to increase the resistors to 15ohms with an idss that high. Should I do that or keep the resistors at 10ohms?
I would like to know also. Hope someone replies !!!
I’m going to build the ISHIKAWA daughter boards and have match JFETs of 10.82 idss. I read somewhere a recommendation to increase the resistors to 15ohms with an idss that high. Should I do that or keep the resistors at 10ohms?
I would like to know also. Hope someone replies !!!
I read the same advice. The idss of my Jfets is a shade over 10mA and I'll be using 15R resistors.
I read the same advice. The idss of my Jfets is a shade over 10mA and I'll be using 15R resistors.
Skylar,
Thank you. I think I will do the same thing.
- Home
- Amplifiers
- Pass Labs
- The diyAudio First Watt M2x