It means that people forget this so many times that he should add it to every post he makes.
(my signature line is: Candidates for the Darwin Award should not read this author. )
Speaking of which, is there a Darwin's Award for the candidates in electronics?
I almost earned it when I was in high school.
I removed a big capacitor in the high voltage section of an oscilloscope (without discharging it first). It bit me so hard my arm contracted and threw the cap across the room. I was so stupid I went over, picked it up, and got bit again!
I now work with MUCH higher voltages. No one is allowed to come near me, or to even talk to me, while I am doing a high voltage test.
I removed a big capacitor in the high voltage section of an oscilloscope (without discharging it first). It bit me so hard my arm contracted and threw the cap across the room. I was so stupid I went over, picked it up, and got bit again!
I now work with MUCH higher voltages. No one is allowed to come near me, or to even talk to me, while I am doing a high voltage test.
apex sir,
i supply 70vdc, and the dc offset is showing 145mv dc.
i connect input gnd to psu gnd.
what will be the problem?
little sound is coming out with low volume (volume control i turned to ccw 0 level but little sound is coming through speaker)
Match input transistors to get under 30mV dc offset. 145mV dc offset and little sound on 0 level is not big problem.
Regards
Simple Soft-start, DC, Thermal and Overload Protect with NE555. Use single 12vac for suply.
hi apex sir,
the protection board in progress.
is this protection suitable for h900?
Attachments
hi apex sir,
the protection board in progress.
is this protection suitable for h900?
No, PRO pins are not compatible on H900 and HV23, but if you don't want use overload protect you can use this protect with any amp.
No, PRO pins are not compatible on H900 and HV23, but if you don't want use overload protect you can use this protect with any amp.
I've built your HV 350 PSU,can I use it for B500??
Does it protector will working good??
Regards
I've built your HV 350 PSU,can I use it for B500??
Does it protector will working good??
Regards
Yes, but without overload protect,
Regards
hi apex sir,
i finished and tested this protect, but not working,
what will be the problem?
Protect can't work without 10k NTC (thermal protect), but you can use 10k resistor instead NTC for test.
Regards
Protect can't work without 10k NTC (thermal protect), but you can use 10k resistor instead NTC for test.
Regards
thanks sir for the reply.
ok i will buy 10k ntc and check.
hi apex sir,
now i put 10k ntc .
now the protect circuit is working, but when power on , the relay delay time is one second ,because the led indicator only blinking once and after relay connects the led permanently lights on, how can i increase the delay time to 3 or 5 seconds?
now i put 10k ntc .
now the protect circuit is working, but when power on , the relay delay time is one second ,because the led indicator only blinking once and after relay connects the led permanently lights on, how can i increase the delay time to 3 or 5 seconds?
hello sir ..can u pls share pcb lay out and digram..???. thank u...hi apex sir,
i finished and tested this protect, but not working,
what will be the problem?
hi apex sir,
now i put 10k ntc .
now the protect circuit is working, but when power on , the relay delay time is one second ,because the led indicator only blinking once and after relay connects the led permanently lights on, how can i increase the delay time to 3 or 5 seconds?
now i put 10k ntc .
now the protect circuit is working, but when power on , the relay delay time is one second ,because the led indicator only blinking once and after relay connects the led permanently lights on, how can i increase the delay time to 3 or 5 seconds?
Attachments
- Home
- Amplifiers
- Solid State
- MOSFET Amplifier IRFP240/IRFP9240