ReceiverPi DDC is really powerful. Here is another example project which I like very much. It make the whole project very organized. Software and hardware issue are on longer mixed up by using the RPi free configuration:
Flagship full-size full-function RPi free DDC streamer (or DAC)
Configurations:
#35C StationPi SMT
#20C TransportPi AES or #17B HdmiPi Pro or #4B ESS Dual Mono II DAC and I/V board
#1D FifoPiQ7
#19D ReceiverPi DDC
#49B MonitorPi Pro
#50A GPIO extender
Apple remote control (optional)
Power supplies:
#32B LinearPi Solo + #25B UcConditioner 5V (optional)
#41C UcPure MkIII 3.3V
Installations:
Possible upgrade:
FlagshipFullSizeDDC
Flagship full-size full-function RPi free DDC streamer (or DAC)
Configurations:
#35C StationPi SMT
#20C TransportPi AES or #17B HdmiPi Pro or #4B ESS Dual Mono II DAC and I/V board
#1D FifoPiQ7
#19D ReceiverPi DDC
#49B MonitorPi Pro
#50A GPIO extender
Apple remote control (optional)
Power supplies:
#32B LinearPi Solo + #25B UcConditioner 5V (optional)
#41C UcPure MkIII 3.3V
Installations:
- Install the boards as the picture, use all 13mm standoffs
- Connect 5V to J3 of the StationPi SMT, make sure J9 1-2,2-4 are jumped
- Connect 3.3V to J5 of FifoPi from J9 of UcPure
- Connect U.FL coaxial cable from MCLK of FifoPi to the HdmiPi Pro or TransportPi AES or DAC
- Connect the control cable from J6 of the MonitorPi Pro to J7 of the ReceiverPi DDC
- Connect SYNC charging control cable from J5 of the MonitorPi Pro to J10 of the PurePi II
Possible upgrade:
- Upgrade FifoPi Clocks to #80A and #80B SC-Pure 45/49 clocks
- Connect 3.3V to J5 of FifoPi from the continuous output J10 or J13 of UcPure
- Insatll a RaspberryPi if really want
FlagshipFullSizeDDC
Original Amanero is also not expensive. I bought the original. See the one in the above picture.
https://amanero.com/
https://amanero.com/
The header spacing doesn't match the Amanero USB.
http://www.twistedpearaudio.com/digital/amanero.aspx
Can also buy them here. Shipping from Italy was expensive.
Can also buy them here. Shipping from Italy was expensive.
I use Hdmi Pro.Thank you for the clue.
I'm a little surprised that there is no such setting in the FifoPi Q7 controller itself, if without this option its functioning is impossible.
In the manual for MonitorPI I can't see a single hint of such an option or description of its change too.
How do you transfer a digital stream from FifoPi Q7 to your Audio-Gd R7 He Mk2? I mean, do you use any interface or feed i2s directly?
I’ve got one. What does CCOM do?Anyone, who has MonitorPi Pro, can you test for me the following?
Thank you!
- Turn off the 'Continous clock output mode' in the advanced menu
- With remote control, switch to an input which has no signal (e.g. HDMI)
- Check if the remote control stops working or not
- Home
- Source & Line
- Digital Line Level
- Asynchronous I2S FIFO project, an ultimate weapon to fight the jitter