More boards on the way!
This is great Mark! Thank you for sharing your shipping experience. I just placed an order for 20 boards with JLCPCB. I've done several board runs with them and have always had great results. The boards are as listed previously.
2mm Thick FR4
Red Solder Mask
2oz Copper
ENIG Finish
$7 per board plus packing and shipping (international tracking and insurance would be extra if you want them)
PM me if your interested. I accept PayPal. I should have the boards in hand around the end of next week.
Between this and FreeCrowder's order we should be able to get a few more AB100's up and running. 🙂
Thanks again to Papa Pass for his generosity!!!!!
This is great Mark! Thank you for sharing your shipping experience. I just placed an order for 20 boards with JLCPCB. I've done several board runs with them and have always had great results. The boards are as listed previously.
2mm Thick FR4
Red Solder Mask
2oz Copper
ENIG Finish
$7 per board plus packing and shipping (international tracking and insurance would be extra if you want them)
PM me if your interested. I accept PayPal. I should have the boards in hand around the end of next week.
Between this and FreeCrowder's order we should be able to get a few more AB100's up and running. 🙂
Thanks again to Papa Pass for his generosity!!!!!
Just so everyone knows my boards are the same cost but they aren't quite as good as far as the thickness and copper. Mine will be 1.6mm and 1OZ copper. the same quality from where I ordered doubled the price. Should still be quite good for the job though.
How are you guys getting these boards at 2mm and 2oz copper so cheap!! I run them through 2 different places and can only get down to 10-11 bucks for 20.
Ordering 20 boards from JLCPCB + shipping from Hong Kong with Aramex Global Shopper works out just under $7 each.
That's for 2mm FR4, 2oz copper & ENIG finish.
That's for 2mm FR4, 2oz copper & ENIG finish.
Last edited:
You use what as output transistors? tip142/147 or other things? Too bad that can not with std03n/ std03p because I like these transistors, I have already made a montage with the LME4702and are it is beautiful
I think they can be used - of course you will need custom pcb and 2-3 pairs will be enough...
My reduced AB 100 to AB 60 is slowly being processed- still have to make PCB and wait for the parts to be delivered...
My reduced AB 100 to AB 60 is slowly being processed- still have to make PCB and wait for the parts to be delivered...
Attachments
Last edited:
no reply yet anyone for post #553?
I am just a 'dime a dozen' PCB designer (and very bad at it too!
). I sometimes wonder at why I am messing around threads for and by intellectuals😱
regards
Prasi
I am just a 'dime a dozen' PCB designer (and very bad at it too!
). I sometimes wonder at why I am messing around threads for and by intellectuals😱 regards
Prasi
no reply yet anyone for post #553?
I am just a 'dime a dozen' PCB designer (and very bad at it too!
regards
Prasi
If you're referring R35 it's been mentioned a few times ... Consensus seems to be it's not necessary. Although I didn't see Mr. Pass chip in.
Hello uber,
I was wondering if something like this can be done, with R35 being used to lift input ground, R2 ground and NFB cap ground by 10 ohm resistor from the PSU ground.
regards
Prasi
Attachments
Yes, you can do that.
Usually the idea is to break a ground loop in an two channel amplifier having
common input ground. Magnetic fields inside the amp and outside can cause
current to circulate from one channel ground back to the source and then
back to the amp via the other channel's cable ground and ultimately causing
noise pick up. If you break one channels input ground connection and replace
it with a 10 ohm or so resistor, you can break that loop.
Doesn't always work, but easy enough to try.
Usually the idea is to break a ground loop in an two channel amplifier having
common input ground. Magnetic fields inside the amp and outside can cause
current to circulate from one channel ground back to the source and then
back to the amp via the other channel's cable ground and ultimately causing
noise pick up. If you break one channels input ground connection and replace
it with a 10 ohm or so resistor, you can break that loop.
Doesn't always work, but easy enough to try.
Hi Prasi
If you're working on a layout, I hope that you're going to share the Gerbers. 😉
Hi All,
I currently have 6 boards (3 stereo pairs) left if anyone is interested. I should receive the boards on Wednesday, but I probably won’t have time to ship out until the following week due to the holiday.
I currently have 6 boards (3 stereo pairs) left if anyone is interested. I should receive the boards on Wednesday, but I probably won’t have time to ship out until the following week due to the holiday.
That's two good vendors.
I remember the days when I had to tape this stuff up, have it photographed
to separate blue/red/black and send that off.
Only took a month and $1000 for a single prototype...
Who sez there's no progress?
I remember the days when I had to tape this stuff up, have it photographed
to separate blue/red/black and send that off.
Only took a month and $1000 for a single prototype...
Who sez there's no progress?
Pretty amazing stuff NP! Thanks again for the great design and the gerbers!
FYI, all of my boards are now spoken for. Thanks everyone!
FYI, all of my boards are now spoken for. Thanks everyone!
Last edited:
So I'm stuffing my first board and I want to clarify some values. I understand value and multiplier but still have some questions. Base resistors are 221. is that 22x1Multi equals 220ohm? Also R7 2210 221x 0 multiplier equals 221ohm? R5= 475 ohm?
