in 38 pages still do not know if it works have not been bine.etc if I hear that still remain in the scheme Kon Electronic :: View topic - amp leco
Try to fit it in 260x112mm, it's same dimension as amp pcb for 3U.
Regards
Ok, here are the 2 Versions for optional diode.
Regards,
Attachments
Anyone want transformers
I have a few of these I need to offload soon. Ping me if interested.
Input 100v/110v/220v
Output: 62- 0 -62 or 69-0-69vac or +/-84vdc or +/- 99vdc
700va
Metal encapsulated
Can parallel 2 to get 1.4kVA
These are very tight tolerances. There is less than 0.1mVac difference in secondary voltage of 2 transformers.
They are pull outs form Adcom GFA-555ii's
Price negotiabe: PM me.
I have a few of these I need to offload soon. Ping me if interested.
Input 100v/110v/220v
Output: 62- 0 -62 or 69-0-69vac or +/-84vdc or +/- 99vdc
700va
Metal encapsulated
Can parallel 2 to get 1.4kVA
These are very tight tolerances. There is less than 0.1mVac difference in secondary voltage of 2 transformers.
They are pull outs form Adcom GFA-555ii's
Price negotiabe: PM me.
Attachments
Ok, here are the 2 Versions for optional diode.
Regards,
Nice work, caps will have better cooling on this pcb, thanks again.
Regards
Nice work, caps will have better cooling on this pcb, thanks again.
Regards
Most welcome...
Setting bias is easy, just adjust about 15 mV on 1R/5W resistors and that is 15mA per output pair or 135mA total.
with vent 'holes'
and now able to lift it out, as a unit
Looks like custom built chopper 🙂
Attachments
I take that as a compliment, thanks
not really a fan of choppers myself.... but that is a cool looking bike
not really a fan of choppers myself.... but that is a cool looking bike
Soft Start w/ Fan Control.
Thanks that is very good idea to integrate this circuits on same pcb.
I suggest to use protect with NE555 for BA1200.
Regards
Attachments
Last edited:
Thanks that is very good idea to integrate this circuits on same pcb.
I suggest to use protect with NE555 for BA1200.
Regards
I'm currently using this protect in my amps but I don't remember if i posted this protect before.
...This is tested and working circuit, just needs to change T9 relay and should be fine for BA1200.
Regards,
Attachments
Thanks
Thanks for taking the time to improve your pcb and porating 5w resistors.
Here's Rev1.2 using 10K/5W resistor.
Regards,
Thanks for taking the time to improve your pcb and porating 5w resistors.
great forum
PCBs very practical and useful, thanks mate, you are a great person, I am pleased to be in this forum with good and friendly people.
Soft Start w/ Fan Control.
I'm currently using this protect in my amps but I don't remember if i posted this protect before.
...This is tested and working circuit, just needs to change T9 relay and should be fine for BA1200.
Regards,
PCBs very practical and useful, thanks mate, you are a great person, I am pleased to be in this forum with good and friendly people.
I'm currently using this protect in my amps but I don't remember if i posted this protect before.
...This is tested and working circuit, just needs to change T9 relay and should be fine for BA1200.
Regards,
You need add output coil and 5W resistor, NTC connection must be change look circuit in post #394.
Regards
You need add output coil and 5W resistor, NTC connection must be change look circuit in post #394.
Regards
Got it... will revise that and make single protect.
Regards,
- Home
- Amplifiers
- Solid State
- 1000W Simple PA Amplifier