About UGS v6.
reading stereophile about the Xp-32 preamp :
any speculations about that "summing junction" ?
reading stereophile about the Xp-32 preamp :
Code:
"The ground of each RCA input is in parallel with pin 1 of the XLR, and
the RCA input feeds a summing junction that, according to
the manual, “[maximizes] the patented supersymmetry (X
circuit) and preserves the balanced character of the XP-32
from input to output when fed from a single-ended source.”
any speculations about that "summing junction" ?
Last edited:
... there's something i need to know to make trigger works ?
i have connected the OUT A from the preamp to an UGS Up with a stereo TRS jack-jack cable.
i expected when waking the preamp up that also the amp will follow, but nothing happens.
Trigger set as : Latched.
any insights ?
thanks
i have connected the OUT A from the preamp to an UGS Up with a stereo TRS jack-jack cable.
i expected when waking the preamp up that also the amp will follow, but nothing happens.
Trigger set as : Latched.
any insights ?
thanks
I second Jacek's suggestion. At one point, the 16 pin IDC connector on the Muse UGS MCU board was rotated 180 degrees compared to the All Inclusive UGS (see: <<UGS - Muse edition - Page 38>> - 30058092 - sur le forum <<Amplis et Preamplis>> - 1056 - du site Homecinema-fr.com).
I'm not sure if that was changed on the latest PCB. I just verified on a picture of my implementation and the IDC orientation cut-out is facing the top of the MCU, if that can help.
Paul
I'm not sure if that was changed on the latest PCB. I just verified on a picture of my implementation and the IDC orientation cut-out is facing the top of the MCU, if that can help.
Paul
I think I have found the issue... I have not thought and just terminated the idc cable as a previous photo reported.You can also trace out pin 1 or pin 16 to make sure the orientation is correct.
Paul
Now i can see from yours that is indeed reversed from what I have.
Tomorrow i will try to fix it.
Should be easy enough.
Thanks !
i think is fixed !
wrong cable orientation.
one new "issue" i have now, quite unavoidable i suppose (initialization) is that when i power ON the preamp (i mean, switching the powersupply on) also the output is triggered and the amp is turned on. that happens while the preamp is in "standby".
then when i switch on everything works... but the first "false" trigger happens regardless.
nice nonetheless...
wrong cable orientation.
one new "issue" i have now, quite unavoidable i suppose (initialization) is that when i power ON the preamp (i mean, switching the powersupply on) also the output is triggered and the amp is turned on. that happens while the preamp is in "standby".
then when i switch on everything works... but the first "false" trigger happens regardless.
nice nonetheless...
This 'pulse' type of triggering is sometimes susceptible to false triggering, especially if trigger cables are long. That is due to various interferences inducted in those cables on the events like powering something else in close proximity which induce strong enough impulse in this cable to trigger UP triggering circuit. In my setup this is happening quite rare so I left this as it is however if this will be a problem you may want to decrease sensitivity of trigger input in UP boards or modify it to use 'level' type instead.
If you need to modify the UP for level triggering, here is an interface front-end that converts level to pulse.
Full story in French : <<[UP] Un trigger normalise>> - 30059254 - sur le forum <<Amplis et Preamplis>> - 1056 - du site Homecinema-fr.com
Full story in French : <<[UP] Un trigger normalise>> - 30059254 - sur le forum <<Amplis et Preamplis>> - 1056 - du site Homecinema-fr.com
Last edited:
If you need to modify the UP for level triggering, here is an interface front-end that converts level to pulse.
Full story in French : <<[UP] Un trigger normalise>> - 30059254 - sur le forum <<Amplis et Preamplis>> - 1056 - du site Homecinema-fr.com
thanks.
this pulse "false triggering" problem between muse pre <-> up2 was the last pish i needed in order to start re-designing the power "manager" board for the Up.
i am a very simple man, and i have already put an stm32 in it to do all the "heavy lifting".
As the amplifier has two "huge" power transformers, i will sequence the startup, one chanel at time.
In this whole contraption, implementing a level trigger is quite trivial.
But i am going OT.
i will post my progressess on another thread !
- Home
- Amplifiers
- Pass Labs
- UGS-muse preamp GB