I didn't remove all stereo parts yet in Rch amp and some things intentionally differ between left and right here🙂 Left ch amp had a defective 1nF cap in output, you might see leads and the new one beneath the pcb🙂 leads will be shortened, just wanted to be sure there was music now jeje "pock-pock-pock'' was all sound that came out, speaker moving 4 mm, loud for small part
Attachments
I didn't remove all stereo parts yet in Rch amp and some things intentionally differ between left and right here🙂 Left ch amp had a defective 1nF cap in output, you might see leads and the new one beneath the pcb🙂 leads will be shortened, just wanted to be sure there was music now jeje "pock-pock-pock'' was all sound that came out, speaker moving 4 mm, loud for small part
Just curious, is this Hiamplifier's board?
Regards,
hiamplifier boards in PBTL, tested Rch board in stereo first. very silent, only little hiss audible with ear almost touching speaker, 25cm in front of speaker I can't hear it, sure 3110 is couple of times louder, I do hear that 25cm away from speaker(hiss) but all audiosets here are louder(hiss) than both tpa's. 3116 turn-on pop barely noticable in PBTL, was there in stereo mode, also hiss was a little louder in stereo, especially in left ch. Is that because AVCC is connected on the left side maybe??
I will only compare some shielded inductors, icecomponent and wurths now, they look better mechanically 😀 and will try filterless just before they are added to speaker (wirelenght inside speaker is ~1meter now).
I will only compare some shielded inductors, icecomponent and wurths now, they look better mechanically 😀 and will try filterless just before they are added to speaker (wirelenght inside speaker is ~1meter now).
This weekend I built a totally over-kill linear regulated power supply for a TPA3116 (black & blue board from YJ).
The sonic difference is stunning.
Now I'm going to build one for my 3110.
The sonic difference is stunning.
Now I'm going to build one for my 3110.
Attachments
SMPS or linear power supply no brainier.This weekend I built a totally over-kill linear regulated power supply for a TPA3116 (black & blue board from YJ).
The sonic difference is stunning.
Now I'm going to build one for my 3110.
From this Universal Laptop Adapter 100W LCD Display AC DC Car Charger Notebook Adaptor | eBay to this New High Power Dimmable LM338K in 3 36V Max 40V Out 1 2 30V 5A Converter | eBay
good sonic difference. (red YJ 2.0 board) Try to put, at the power input 2200uF ... 4700uF or any cap, it is even beater.
This weekend I built a totally over-kill linear regulated power supply for a TPA3116 (black & blue board from YJ).
The sonic difference is stunning.
Now I'm going to build one for my 3110.
KJA,
As usual, very nice build. That carbon fiber sheet is a nice touch!
Looks like I have to get a blue board too.
Regards,
TPA3116
Details would be appreciated!
This weekend I built a totally over-kill linear regulated power supply for a TPA3116 (black & blue board from YJ).
The sonic difference is stunning.
Now I'm going to build one for my 3110.
Details would be appreciated!
SMPS or linear power supply no brainier.
From this Universal Laptop Adapter 100W LCD Display AC DC Car Charger Notebook Adaptor | eBay to this New High Power Dimmable LM338K in 3 36V Max 40V Out 1 2 30V 5A Converter | eBay
good sonic difference. (red YJ 2.0 board) Try to put, at the power input 2200uF ... 4700uF or any cap, it is even beater.
I've been hemming and hawing over power supplies as of late. Have you tried both?
I have two pairs of speakers that I wish to power with two boards (my preamp has two pre outs). Should I get one of those Mean Well SMPS, which has the two DC outputs, and house it and the two boards in one chassis?
+1 on the KJA-TPA envy! 🙂
Nice carbon fiber treatment!
What kind of speaker output connector is that (the black ones above the bananas)?
Also, what are the specifics of your linear PS?
Nice carbon fiber treatment!
What kind of speaker output connector is that (the black ones above the bananas)?
Also, what are the specifics of your linear PS?
Several more. These were the better ones.Have you tried both?
It all depends on how good speakers do you have and how much you want to invest money and effort. If you have good speakers and want better sound go with a separate linear power supply. More details, dipper bass... My Fostex fe207e reveals every detail. Some time it is not good thing.I have two pairs of speakers that I wish to power with two boards (my preamp has two pre outs). Should I get one of those Mean Well SMPS, which has the two DC outputs, and house it and the two boards in one chassis?
SMPS or linear power supply no brainier.
From this Universal Laptop Adapter 100W LCD Display AC DC Car Charger Notebook Adaptor | eBay to this New High Power Dimmable LM338K in 3 36V Max 40V Out 1 2 30V 5A Converter | eBay
good sonic difference. (red YJ 2.0 board) Try to put, at the power input 2200uF ... 4700uF or any cap, it is even beater.
What does the second one do? LM338K new power dimmable?
Variable linear PS.
I'm a newbie, so you have to combine the first power supply link with the second power supply link? Or is the second link it's own power supply? Can you explain how it works or connects? Is it 110v?
Comparing inductors on a single speaker in mono is more difficult than I thought, probably because I usually listen to stereo jeje. The stereo board with only icecomponent inductors had remarkedly more bass volume than the dual pbtl wurth/icecomponent, in mono the icecomponent side has a little more bass volume than the wurth side, I think I must test 1 inductor at a time in stereo jeje. Due to added bulkcapacitor value and similar input caps sure 3110 bass output is more impressive. In high frequency detail the 3116's seem superior, but that could be decoupling/bulk supply caps related too, I previously liked the EKY Chemicons in a different amp for same reason, clarity, detail, layering of highs without the hard/harsch part FR/FM Panasonics seem to add to my system/speakers. My Primare CDplayer is exclusively Panasonic cap's so that could be reason too that another stage with Panasonics is too much 🙂
This weekend I built a totally over-kill linear regulated power supply for a TPA3116 (black & blue board from YJ).
The sonic difference is stunning.
Now I'm going to build one for my 3110.
What does the carbon fiber do? I see the Jupiter. What else is goin' on in there?
*sniff* I could totally build mine like that if I wanted to.
Gotta spill the beans on the PS!
sure 3110 bass output is more impressive
You think the Sure 3110 has more impressive bass than the YJ Blue 3116? I am listening to a Sure 3110 on my Vifa DCR's as I type, the bass is very nice but not sure if better...
Thanks Lo_Tse, Octavia, xrk971, wushuliu, etc...
Carbon fiber is excellent for vibration control. The entire base is a 1/2" carbon fiber laminate from Dragonplate .
The 3116 board is also mounted on an second piece of the 1/2" laminate.
The rear panel loaded with jacks is a 1/8" uni prepreg carbon fiber sheet.
xrk971, the upper outputs are Cardas Patented Posts.
elb, xrk971 ...
As far as details.... nothing too fancy. A good transformer, quality bridge rectifier, caps etc..
I spent a good week experimenting with different devices and configurations.
I built the box for evaluating parts, circuits.... it makes a great integrated amp though. 🙂
Carbon fiber is excellent for vibration control. The entire base is a 1/2" carbon fiber laminate from Dragonplate .
The 3116 board is also mounted on an second piece of the 1/2" laminate.
The rear panel loaded with jacks is a 1/8" uni prepreg carbon fiber sheet.
xrk971, the upper outputs are Cardas Patented Posts.
elb, xrk971 ...
As far as details.... nothing too fancy. A good transformer, quality bridge rectifier, caps etc..
I spent a good week experimenting with different devices and configurations.
I built the box for evaluating parts, circuits.... it makes a great integrated amp though. 🙂
Attachments
Carbon fiber can also be good at suppressing RFI as it is conductive - but the whole box needs to be made of it like a Faraday cage. Spacecraft electronic boxes are sometime made of CF for lightweight EMI/RFI suppression.
Carbon fiber can also be good at suppressing RFI as it is conductive - but the whole box needs to be made of it like a Faraday cage. Spacecraft electronic boxes are sometime made of CF for lightweight EMI/RFI suppression.
Good point! I'd love to build a whole chassis from it. I love the stuff... I'm using vdH CC-18 carbon wire on a couple of the inputs and these carbon fiber footers.
Attachments
- Home
- Amplifiers
- Class D
- TPA3116D2 Amp