Building process - The loudspeaker 1

20220527_103754.jpg


20220527_105322.jpg
 
I have had good luck with the Jasper circle cut jig. Mine will cut a circle from 1.5 inch to 18 inch diameter.

https://jaspertools.com/
I have the same one and it is good, the only downside is that it only goes up in fixed increments so sometimes getting a really tight fit is hard.

The small jig made in this video looks very useful to me, as the larger one shown in there is too.

 
Yes, I understand, FA251 is only 125 Watts into 8 Ohm. FA501 is 270 Watts, and FA123 in BTL-mode is 250 Watts.
Hey!
So, Seems like Im an idiot... My Hypex setup was as follow: Using the analog Crossover of the Speaker to do the job
hypex-bi-amping-2.png


I had enough of not having good bass so I just removed the bass crossover section and connected the Hypex directly to the BMS Driver using Troels pre-written graphs which looks like this:

TL2-6_preset-1.png
TL2-6_preset-2.png


Then I have noticed that all this time my Hypex was set at -96DB Gain... Thats why I always had the gain knob turned all the way up... Idiot!!!

So, I have set the gain right, uploaded the pre-written cross (using the Preset 2 with 4db boost... ) and discovered a whole new world.

So I am taking back what I said about the Hypex... Though would be even better to have the FA501... or 1000Wattts per Channel Like TheoSeawden suggested.

Really incredible what this BMS can do!
 
Haha, beautiful. Looking forward for another video of yours!

Are you not using the analoge crossover for bass anymore at all now?

So I am taking back what I said about the Hypex... Though would be even better to have the FA501... or 1000Wattts per Channel Like TheoSeawden suggested.

As I had said before, I could not hear a difference between the 75 Watts into 8 Ohm and 250 Watts into 8 Ohm BTL-mode setup. Only that after I had changed to a smaller enclosure and different bass driver (from Faital 12PR320 to PHL 3411) I needed much more energy for my assisted 6th-order tuning when playing peaks. This is because the enclosure is "too small" without assist.
 
  • Like
Reactions: noamgeller
Then I have noticed that all this time my Hypex was set at -96DB Gain... Thats why I always had the gain knob turned all the way up... Idiot!!!
I'm glad you found out the issue! I must admit I was puzzled by your perception of having more bass on a 18" woofer powered by a SET amp vs hypex!!! Now I know why it sounded that way, it was basically a SET amp vs nothing 😀
 
  • Like
Reactions: noamgeller
I'm glad you found out the issue! I must admit I was puzzled by your perception of having more bass on a 18" woofer powered by a SET amp vs hypex!!! Now I know why it sounded that way, it was basically a SET amp vs nothing 😀
Exactly!
Ho well, it has also the advanteges of discovering your speaker abilitys driver by driver and every week unfold a new discovery 😊
 
  • Like
Reactions: Wright
Haha, beautiful. Looking forward for another video of yours!

Are you not using the analoge crossover for bass anymore at all now?



As I had said before, I could not hear a difference between the 75 Watts into 8 Ohm and 250 Watts into 8 Ohm BTL-mode setup. Only that after I had changed to a smaller enclosure and different bass driver (from Faital 12PR320 to PHL 3411) I needed much more energy for my assisted 6th-order tuning when playing peaks. This is because the enclosure is "too small" without assist.
Ho man... well now that we have bass its time to see if I can adress the room modes as you suggested.
The Analoge Crossover sits on the shelf for the time being, using only the Hypex built in DSP. I've made the change yesterday so I had only little time to listen... but in some tracks it was like "what the f@@ck?? "where did that come from" kinda moments 😀

Which brings me to the next "problem" , Videos taking from the system is so frustrating!! sitting there being ohw struck, then picking the phone and trying to capture it... just to realise that nothing really comes through... the voices in particlure have a great sense of presense especially with the SET amp... through to phone thou, nothing! Then instead of being happy that I can share such moments with the people who seek it, you kinda feel pitiful and lame. which sucks.
But I'll probably coudln't help my self and make a new one. This time with the lowest octave as well 😛
 
And a side note on veneer. I am afraid it is going to be expensive, especially 2mm walnut veneers, that's why I'm waiting with it, was an expensive project till now and I need to save some money... besides, lifting them and carrying them down the stairs is not something I'm looking forward to 🙄
 
  • Like
Reactions: Quaesitor300