The total line length excluding port will then be 47 inch, which will be a too high cabinet. Would it be possible to half that by adding a fold, or does that bring other complications?
You can fold it.
I would want it even higher. Driver is too low as a floorstander. It should be around 1 meter from floor, if you are sitting.
But I don't know how you plan to use them. You can optimize them to fit your needs. If you don't need it tall, bass reflex (shorter and fatter) might be a better option.
What about this (it is below 40" and has weaker harmonics):
I would want it even higher. Driver is too low as a floorstander. It should be around 1 meter from floor, if you are sitting.
But I don't know how you plan to use them. You can optimize them to fit your needs. If you don't need it tall, bass reflex (shorter and fatter) might be a better option.
What about this (it is below 40" and has weaker harmonics):
Attachments
Last edited:
Thanks for the suggestions Lightbit. I think I am going forward with the 40 inch straight line. Easier to build and driver center being at 81 cm, bit higher as my current midrange driver, will suit my needs I guess.
Only thing I need to decide is width, as the FC8 is already 220 mm (8.7 inch). From an easthetic opinion, I think 11 inch internal width (12.5 external) will look other than usual.
Only thing I need to decide is width, as the FC8 is already 220 mm (8.7 inch). From an easthetic opinion, I think 11 inch internal width (12.5 external) will look other than usual.
Hello scmeet, Is it possible to get installer for your TL program? I had it long time ago but now after pc change I would like to have it again.
Thank you LightBit, I was trying this one, but it is not possible to install. During installation it connects to server or elsewhere and then error. I have extracted to c: disc but it is not helping. Maybe somebody has some solutions?
LATL app was working fine, but today, I have a bug.
I didn't update anything in my computer, all automatic updates are supposedly turned off, and yet, today, It came up with an error window, and since then, it doesn't want to draw the enclosure in the enclosure window. Only shows the driver, but can't get an enclosure.
I tried restarting the computer, opening saved files I know were good.... no luck.
I'm stuck with no enclosure.
I tried re-installing everything, still no good.
Any help?
Thanks!
I didn't update anything in my computer, all automatic updates are supposedly turned off, and yet, today, It came up with an error window, and since then, it doesn't want to draw the enclosure in the enclosure window. Only shows the driver, but can't get an enclosure.
I tried restarting the computer, opening saved files I know were good.... no luck.
I'm stuck with no enclosure.
I tried re-installing everything, still no good.
Any help?
Thanks!
eesh... nevermind!
Instead of just dragging the folder to the trash and copying a new one, I used Windows own Uninstall in the control panel, and copied a fresh folder.
Got the app working again.
Sorry for the hiccup.
Instead of just dragging the folder to the trash and copying a new one, I used Windows own Uninstall in the control panel, and copied a fresh folder.
Got the app working again.
Sorry for the hiccup.
Hello all , someone here stated some time ago that the LA software for TL design does not give correct results ... so I thought I let you know about another simulation software that has been confirmed to work correctly in dozens of real build and measured speakers , here the link to the website with free demo in german or english :
AJ-Systems - Loudspeaker simulation with AJHorn
Now in version v7 it does nearly any sort of bass loading , and low pass filter effects also accounted for , well worth the money!
have a nice time
AJ-Systems - Loudspeaker simulation with AJHorn
Now in version v7 it does nearly any sort of bass loading , and low pass filter effects also accounted for , well worth the money!
have a nice time
The author confirmed in the post linked below that the tapped horn results were not correct, but as far as I am aware the others should be okay - they appear to be consistent with those of Hornresp.
https://www.diyaudio.com/forums/sof...n-line-modelling-software-53.html#post3744415
What is the density of polyester fiber filling for specific GSM which are available from 100 GSM - 1700 GSM and which one to use as per the HornRes
David, is it possible to add into Hornresp an ability to simulate Helmholtz resonators like on this picture?
Attachments
It is currently possible to specify an absorber chamber using the stubbed horn (SH) model, but that is as far as it goes. I have no plans to take it any further - the inputs are messy enough already, without making them any worse 🙂.
Attachments
Very helpful if someone please could grant a link to download Leonardo's TL software. Many thanks.
It is not straightforward, you shiyld be able to get help here.
https://www.diyaudio.com/community/threads/transmission-line-modelling-software.220421/
dave
https://www.diyaudio.com/community/threads/transmission-line-modelling-software.220421/
dave
Latest SW v. 3.6.3.5
https://web.archive.org/web/20170506211617/http://leonardaudio.co.uk/transmission-line/download/
https://web.archive.org/web/20161204124932/http://www.leonardaudio.co.uk/software/setup.exe
Some minor updates (v. 3.6.3.5):
Bug fix list for all versions
https://web.archive.org/web/20170516170631/http://leonardaudio.co.uk/
Latest user manual v. 3.6.3.4
https://web.archive.org/web/2016120...k/wp-content/uploads/2013/12/TL-UserGuide.pdf
https://web.archive.org/web/20170506211617/http://leonardaudio.co.uk/transmission-line/download/
https://web.archive.org/web/20161204124932/http://www.leonardaudio.co.uk/software/setup.exe
Some minor updates (v. 3.6.3.5):
- Bug fix – When dragging the driver position the status used the wrong units.
- Bug fix – Changing the driver position and pressing enter would not update the model.
- Bug fix – Changing the stuffing density and pressing enter would not update the model.
- When updating the stuffing value via the right click menu and selecting ‘custom’. This can now be entered in the users density unit preference rather than always kg/m³.
Bug fix list for all versions
https://web.archive.org/web/20170516170631/http://leonardaudio.co.uk/
Latest user manual v. 3.6.3.4
https://web.archive.org/web/2016120...k/wp-content/uploads/2013/12/TL-UserGuide.pdf
Last edited:
