@Zek
If i remeber for example in JLE construction is comment "do not use power supply with two output"
So i started to interest why? Could You explain something why one of PSU is good for TPA amplifiers and another not.
Sylph-D200 TPA3255 Stereo (Ready to Run) Amplifier Module | jlelectronicsph
Recommended Power Supply
(NOT INCLUDED)
- 36V DC to 48V DC
- Single supply SMPS 350W or higher.
- DO NOT use dual output types!
Where is the problem?
If i remeber for example in JLE construction is comment "do not use power supply with two output"
So i started to interest why? Could You explain something why one of PSU is good for TPA amplifiers and another not.
Sylph-D200 TPA3255 Stereo (Ready to Run) Amplifier Module | jlelectronicsph
Recommended Power Supply
(NOT INCLUDED)
- 36V DC to 48V DC
- Single supply SMPS 350W or higher.
- DO NOT use dual output types!
Where is the problem?
Last edited:
I guess dual output is 36 - 0 - 36 volt types. If the amp board is for single output then it’s quite obvious
Bendix,
I believe your “two output” is referring to a bipolar power supply.
One that ouputs +/-36v. That type cannot be used with TPA3255 amplifiers.
I believe your “two output” is referring to a bipolar power supply.
One that ouputs +/-36v. That type cannot be used with TPA3255 amplifiers.
Thanks Kjeldsen & Vunce.
I didn't think of it 🙂
I thought it was about something more serious 🙂
I didn't think of it 🙂
I thought it was about something more serious 🙂
is there an alternative for 3e audio TPA3255 1x480W 1Ch
was planing to build two mono units with balanced inputs
can seem to find a suitable replacement since 3e audio no longer has anything stock
any advice?
was planing to build two mono units with balanced inputs
can seem to find a suitable replacement since 3e audio no longer has anything stock
any advice?
You can go for this one, it also supports balanced mode but you need to move a resistor. The OP amps are also updatable in DIP8 socket
Assembler amplificateur de puissance Hifi TPA3255 BTL Mono classe D, 300W C7 36 | AliExpress
If you need a finished Mono Block with a TPA3255 also this one :
Amplificateur de puissance audio mono haut parleur 2020 W, gamme complete/caisson de basses TPA3255, 600 | AliExpress
Last edited:
You re right, two versions : TPA3251 + TPA3255 available.
Same PBC, same components, just a different TPA chip ) my bad
Same PBC, same components, just a different TPA chip ) my bad
D
Deleted member 148505
We have changed the description to "Do NOT use split rail power supply".
We have a cheaper option TICore400M TICore400M TPA3255 PBTL Mono Single Supply RTR Amplifier Module | jlelectronicsph
With jumpers for Slave, PFFB and BAL/SE. OSC IOM/IOP headers for multi device sharing a single power source.
Dual mono setup almost sound the same as the stereo modules. Though I think the sound stage of the mono is "taller" like there's a speaker on top ceiling. But maybe that's just me...
Attachments
In English:
TPA3255 Digital Power Amplifier Board 315Wx2 HiFi Dual Channel High Power Class D Audio Power Amplifier Board|Amplifier| - AliExpress
What case can I use with it? Is there a complete kit, assembled or not?
Aiyima A08 (comes with 36V 9.5A power supply installed)
Attachments
Last edited:
I'm interested in upgrading the caps in the Aiyima A08 if any (even subtle) improvements? Best to just match the values 4x 1000uf 50V caps or could I increase them? If able to increase, max values? and would I need to change anything else? Should I look at changing any of the other caps? Which caps are recommended? Nichicon KW series...? Thanks so much.