Greetings all,
would anyone have a spare PCB for the low noise measurement amp?
Kindest regards,
M
would anyone have a spare PCB for the low noise measurement amp?
Kindest regards,
M
According to record (still needs double checking), we have 5 sets left.
i.e. both the original NJFET version and the PJFET version.
https://www.diyaudio.com/community/...urement-amp-for-ikoflexer.175044/post-5007920
The idea of the P-Version is that you can use it to measure the noise of a PJET.
We can offer these 5 sets in a GB, to minimise admin work.
Else we need to charge extra for handling single orders.
(collecting addresses, packing, customs declaration, queueing at the Post Office, posting tracking number, ..)
If there are 5 takers, we shall charge 120HKD for 2 PCBs including registered air mail, and PP charges.
This is just service and will only cover costs.
Patrick
i.e. both the original NJFET version and the PJFET version.
https://www.diyaudio.com/community/...urement-amp-for-ikoflexer.175044/post-5007920
The idea of the P-Version is that you can use it to measure the noise of a PJET.
We can offer these 5 sets in a GB, to minimise admin work.
Else we need to charge extra for handling single orders.
(collecting addresses, packing, customs declaration, queueing at the Post Office, posting tracking number, ..)
If there are 5 takers, we shall charge 120HKD for 2 PCBs including registered air mail, and PP charges.
This is just service and will only cover costs.
Patrick
Suddenly so much interest !!
mefistofelez asked first, so he has the right to say no before it goes to others.
In the meantime, 2 more earlier requests by PM :
1. mefistofelez (?)
2. woodturner-fran
3. twitchie
4. staccatiss
If no further interests from others, staccatiss can have up to 3 sets.
Let's give it a few days.
Thank you for your interest,
Patrick
mefistofelez asked first, so he has the right to say no before it goes to others.
In the meantime, 2 more earlier requests by PM :
1. mefistofelez (?)
2. woodturner-fran
3. twitchie
4. staccatiss
If no further interests from others, staccatiss can have up to 3 sets.
Let's give it a few days.
Thank you for your interest,
Patrick
Hi Patrick,
yes, yes, and so there is no doubt, yes again. 😀
I would like both the N and P boards. How can we arrange it?
Kindest regards,
M
yes, yes, and so there is no doubt, yes again. 😀
I would like both the N and P boards. How can we arrange it?
Kindest regards,
M
1. mefistofelez
2. woodturner-fran
3. twitchie
4. staccatiss
Let's give it a few more days.
Then we'll let you know how to proceed.
Patrick
2. woodturner-fran
3. twitchie
4. staccatiss
Let's give it a few more days.
Then we'll let you know how to proceed.
Patrick
1. mefistofelez
2. woodturner-fran
3. twitchie
4. staccatiss
5. claudio
So all gone.
We'll get in touch some time next week.
Thanks,
Patrick
2. woodturner-fran
3. twitchie
4. staccatiss
5. claudio
So all gone.
We'll get in touch some time next week.
Thanks,
Patrick
I already have details of woodturner-fran and twitchie.
For the others, please kindly me send a PM with the following details :
DIYA Nickname
Real Name
Postal address
Email address
PP address (if different)
I shall then contact you by email for payment details.
May take a few days.
Thank you for your patience,
XACOO
For the others, please kindly me send a PM with the following details :
DIYA Nickname
Real Name
Postal address
Email address
PP address (if different)
I shall then contact you by email for payment details.
May take a few days.
Thank you for your patience,
XACOO
But not everyone can do such beautiful Vero builds as you can. 🤓
Absolutely immaculate.
Patrick
Absolutely immaculate.
Patrick
Yes, I'm pretty sure I can carve a billet of AL with my chisel, just give me a year or two.
The box is ordinary microwave stuff; it would be costly only if milled
just for the dimensions I want. But I can cut the vector board for the
boxes that I have. The circuit on the vector board is not exactly a
work of art. Just good GND distribution on the top side.
A good source for the milled boxes are wideband microwave
electronis from ALI. Just remove the innards.
I have not done that, but I have just cut an Anritsu 10 GHz
bit error checker to pieces. ( 10G generator missing, and error checker
in unknown state.)
It was filled with milled soap boxes and SMA cables. Most SMAs
were not SMA but PC3.5. Much too precious for audio, but I don't
question that some people here would attest much better bass.
Gerhard
just for the dimensions I want. But I can cut the vector board for the
boxes that I have. The circuit on the vector board is not exactly a
work of art. Just good GND distribution on the top side.
A good source for the milled boxes are wideband microwave
electronis from ALI. Just remove the innards.
I have not done that, but I have just cut an Anritsu 10 GHz
bit error checker to pieces. ( 10G generator missing, and error checker
in unknown state.)
It was filled with milled soap boxes and SMA cables. Most SMAs
were not SMA but PC3.5. Much too precious for audio, but I don't
question that some people here would attest much better bass.
Gerhard
The following have been shipped with tracking number :
1) RC988876134HK to mefistofelez
2) RC988876125HK to woodturner-fran
3) RC988876117HK to twitchie
4) RC988876151HK to staccatiss
One shipment pending, subscriber informed but no response as yet.
XACOO.
1) RC988876134HK to mefistofelez
2) RC988876125HK to woodturner-fran
3) RC988876117HK to twitchie
4) RC988876151HK to staccatiss
One shipment pending, subscriber informed but no response as yet.
XACOO.