15pr400 x2, 34 hz tuning
Nice!
Which comp. driver is mounted to the XT1464?
I don't think I've seen such huge ports so close together before.
No build thread on here, and I just built a turntable to measure polars. Room Eq wizard will be used for measurement data when I have time and weather on my side.
Passive from HF to MR diaphragm, and actively crossed from the compression driver to the woofers.
Good looking turntable, simple but effective.
What's the XO between the BMS and the Faitals?
What's the XO between the BMS and the Faitals?
Last edited:
I'd have to check when I get back home, but I think it was around 625 or 650 hz. I have some data from measuring indoors with a short window, but it's best to post good outdoor measurements. ( I have access to a forklift at work )
That would be the lower limit for the XT1464, not for the BMS.
I expect this speaker to sound excellent (once optimized).
Your speaker would qualify for this thread, if we consider the 4594ND as a single driver (which technically it isn't).
I expect this speaker to sound excellent (once optimized).
Your speaker would qualify for this thread, if we consider the 4594ND as a single driver (which technically it isn't).
Last edited:
I know that you have posted some pictures of the building process on another forum. You definitely don't have to be ashamed of these and you might at least link to that one !
regards
Charles
Agree... most if the pleasure is psychoacoustic highly influenced by what you see too..
If you google the drivers + horn you'll find a thread in another forum.
I leave it up to diyuser2010 to actually post a link.
This appears to be a well thought out project.
These speakers would work at home as well for fullrange PA duties in small venues were ultimate low-end extension isn't needed.
As some members of the (original) thread, I am also curious about the wiring of the woofers.
I leave it up to diyuser2010 to actually post a link.
This appears to be a well thought out project.
These speakers would work at home as well for fullrange PA duties in small venues were ultimate low-end extension isn't needed.
As some members of the (original) thread, I am also curious about the wiring of the woofers.
Last edited:
Faital 15PR400, BMS 4594 MTM - Speaker Design - Data-Bass Forums
Woofers are 4 ohm models, wired in parallel.
You've probably considered wiring in series, or 2x 8 ohm drivers in parallel?
Any updates after the last post in the original thread?
Any updates after the last post in the original thread?
Last edited:
I guess the chaice of parallel 4 Ohm drivers has something to do with the amp that is used. Right ?
Regards
Charles
Regards
Charles
I have briefly considered wiring the drivers in series, though 2 ohm loading is fine for any capable pro amp, and short cable runs. Considering the actual in box impedance, I don't see a problem running parallel 4 ohm drivers.
Completed assembly on 3 cabinets, though the last one is awaiting a small amount of filler work and painting, before reassembly with the drivers.
All of the measurement I have gathered at this time is from indoors, with an 8 foot ceiling so it is of limited value to post in my opinion. They are voiced with a combination of measurement and by ear.
Your raw response in the build thread already looks promising.
Agreed on the load of 4 ohm in parallel for pro amps.
Agreed on the load of 4 ohm in parallel for pro amps.
Nice project ! !
I also use the 4594 on xt1464, in mtm and other designs. Love it...
My 2c on wiring the 15"s.....
I would not do 2R. IME, PLX's dont really like it despite the specs.
(I have plx's, pl3's, and pld's)
Plus, from a little above 100Hz to where ever you end up crossing to the BMS, the entire curve looks close to minimum impedance.
I just don't see any gain in going with parallel? But you must have a reason?
mark100, do you have a thread somewhere?
Which woofers do you use?
Personally, I would prefer series because of efficiency/easier load on (low power) amps.
Many of today's pro amps take a 2R load, but the better ones tend to be quite expensive.
If I understand correctly, diyuser2010 opted for parallel considering heating of the VCs.
Which woofers do you use?
Personally, I would prefer series because of efficiency/easier load on (low power) amps.
Many of today's pro amps take a 2R load, but the better ones tend to be quite expensive.
If I understand correctly, diyuser2010 opted for parallel considering heating of the VCs.
Last edited:
