I stand by my order and can supply both US and European addresses for shipping.
I don't want the "order" to stand open forever, though -- but some weeks is certainly OK with me, particularly if we see progress.
Petter
I don't want the "order" to stand open forever, though -- but some weeks is certainly OK with me, particularly if we see progress.
Petter
Motors
Bernhard,
Somehow this thread has slipped under my radar, probably because I was an early orderer of the motors and pulleys, and I'm not getting email notifications of the thread (I will now!). But just to let you know, I'm still in for two motors and two pulleys for tape drive.
Cheers
Bernhard,
Somehow this thread has slipped under my radar, probably because I was an early orderer of the motors and pulleys, and I'm not getting email notifications of the thread (I will now!). But just to let you know, I'm still in for two motors and two pulleys for tape drive.
Cheers
Hi guys,
Sorry for the delay. Been too busy lately to check this forum on a daily basis. I fear that the group purchase will not happen. The final quote when I actually went to buy was $19.50 per capacitor! They really didn't want to do the order. Too much money for me to pay out.
I really tried...
Best Regards,
Dale
Sorry for the delay. Been too busy lately to check this forum on a daily basis. I fear that the group purchase will not happen. The final quote when I actually went to buy was $19.50 per capacitor! They really didn't want to do the order. Too much money for me to pay out.
I really tried...
Best Regards,
Dale
harvardian said:
I fear that the group purchase will not happen.
That's why I said I'd be buying 30.😉 😉
hmmm.... tis pity tis true and pity tis tis true. Nay tis a tragedy. Got some vintage pio's in the meanwhile but still need the 0.47uF to parallel and make up full cap value on my pre-amp. Some budget Ansar supersounds are doing a stirling job there at the moment. Can't wait to remove those dry polyprops and get all oils in.
All,
let's mourne for the 1µ0 if the guy tells me none are left.
Until then, let's think positive!
If there are some left, i will still hav eto go over the distributor, but i will get a price below $14 a piece, maybe considerably.
let's mourne for the 1µ0 if the guy tells me none are left.
Until then, let's think positive!

If there are some left, i will still hav eto go over the distributor, but i will get a price below $14 a piece, maybe considerably.
All,
got response from Epcos already .
They still have thousands, i guess we get our order thru. 🙂
got response from Epcos already .
They still have thousands, i guess we get our order thru. 🙂
Epcos: Still have thousands
That is great news indeed! I am considering purchasing more than my original order depeding on price point.
Petter
That is great news indeed! I am considering purchasing more than my original order depeding on price point.
Petter
Pulley list still open?
Hello Bernhard,
Sent an email via the list in regard to getting on the pulley order list. Haven't had a response - noting that you might be busy with other things.
Thanks
Mike
Hello Bernhard,
Sent an email via the list in regard to getting on the pulley order list. Haven't had a response - noting that you might be busy with other things.
Thanks
Mike
Mike,
Pulley list still open. And, as i said, i may dig out another pair of maxons.
I care tomorrow that the purchasing list is updated.
Somehow the email starved in my sendbox, went out today.
All maxon fans,,
maybe you care to look in the analog board after my strobe flasher, in the DIY TT motor thread . You will need something similar to that to adjust the voltage regulator for proper motor speed.
Then tell me who wants just the crystal or the whole thing as a kit. Or as assembled circuit, but you will have to bribe me a bit for that . 🙂
Pulley list still open. And, as i said, i may dig out another pair of maxons.
I care tomorrow that the purchasing list is updated.
Somehow the email starved in my sendbox, went out today.
All maxon fans,,
maybe you care to look in the analog board after my strobe flasher, in the DIY TT motor thread . You will need something similar to that to adjust the voltage regulator for proper motor speed.
Then tell me who wants just the crystal or the whole thing as a kit. Or as assembled circuit, but you will have to bribe me a bit for that . 🙂
All,
order list updated.
Coming Monday i will contact Epcos to order the MKVs. Until then i am listening to orders and to order retractions.
On Monday i will order as displayed on the order list.
order list updated.
Coming Monday i will contact Epcos to order the MKVs. Until then i am listening to orders and to order retractions.
On Monday i will order as displayed on the order list.
Do we have an approximate price point for MKV's? I am considering upping my order from 20 to ?? but that will be based on the price.
Petter
Petter
Petter and all,
i hope to arrive at a price of $10 per piece, maybe better. No idea how low i can get the price, but US$14 i am not willing to swallow.
This year there was a sale at Conrad, haviong prices at about $6 but who knows if Conrad sold a surplus lot? Anyway, it's indicating how the negotiation bandwidth is.
If $6 can be reached, i will try to kick myself -- i paid much more at Farnell Germany just to make sure i stil get some.
That's life.
i hope to arrive at a price of $10 per piece, maybe better. No idea how low i can get the price, but US$14 i am not willing to swallow.
This year there was a sale at Conrad, haviong prices at about $6 but who knows if Conrad sold a surplus lot? Anyway, it's indicating how the negotiation bandwidth is.
If $6 can be reached, i will try to kick myself -- i paid much more at Farnell Germany just to make sure i stil get some.
That's life.
Yes please!120 Hz Strobe flasher, quartz crystal stabilized, complete:
dice45: 1x
hifidaddy: 1x
peterr: ?
All,
sorry, was occupied.
Petter,
what do i hear from you?
I want to place the order and start dickering 🙂
sorry, was occupied.
Petter,
what do i hear from you?
I want to place the order and start dickering 🙂
MKV order going out today
All,
for a while i was unable to reach the Epcos representative i had contact with.
Today i spoke to him on the phone and the order is going out today.
Just wanted to let you all know.
All,
for a while i was unable to reach the Epcos representative i had contact with.
Today i spoke to him on the phone and the order is going out today.
Just wanted to let you all know.
All,
wanted to let you know the MKV deal is still alive.
I got contacted yesterday from the Epcos representative that the final order is transferred to the distributor now.
wanted to let you know the MKV deal is still alive.
I got contacted yesterday from the Epcos representative that the final order is transferred to the distributor now.
- Status
- Not open for further replies.
- Home
- Design & Build
- Parts
- Group purchase of EPCOS B25839 MKV caps and TT maxon motors