Sorry if this has been asked before, but I'd like to try my hands at making an F6, but my space is such it would be really nice to do a pair of small mono enclosures, as opposed to a very large 5U enclosure. Is there a suitable case and transformer?
Best,
Erik
Best,
Erik
Hi Chatziva,
Thanks! 🙂 The 5u seemed huge! The amp camp boxes seem ideal, but of course I have no idea about power, heat, fit. I just wish I could combine the two "kits" or get a turn-key F6.
Best,
Erik
4U should be perfect and is what I am building mine in. 5U is huge, but if you might switch out to another amp later it might be good. I used 5U for BA-3 Amp...there is lots of room for everything in there, 4U is a little cramped, I may put transformer up on end like 6L6 did in his F6 build thread.
http://www.diyaudio.com/forums/pass-labs/277850-f6-illustrated-build-guide.html
5U has plenty of room for everything and more sink for hotter projects. I plan on another 4U for M-2, two more 5U for BBA-3 monoblocks.🙂
Russellc
Last edited:
I would like to see the collected knowledge in a simple table where one can look up if e.g. the CX1 requires 5U or 4U, and necessary depth. Same for ZV9, F series and so on. Maybe also max ambient temperature should be indicated
A question for you palstanturhin, how did you trim the diamond buffer to zero offset? And does it drift particularly as the bjt's warm up?
...and don't worry about answering! I see you have already covered that off to some degree earlier 🙂
Hey! 🙂
Matching is not critical.
However, if you are afraid of feeding some DC to the transformer, match the diamond first stage NPN/PNP.
That alone usually does the trick.
If you are a perfectionist, match the second stage also. But first stage is more important.
The prototype tests was done with an unmatched diamond.
thanks for getting back!
Thanks!
DC - That was indeed why I was asking. I'm busily SPICEing a few variants of the buffer at the moment, using this as a starting point. Ive a built f6 here in front of me but the jfets are not at all well matched, so my thought is to retro fit the diamond buffer and use the jfets elsewhere... 🙂
Another question if i may? Theres a couple of 'extra' caps on the pcb around the diamond that aren't on the schematic. Before I trace them through, what are they for/ where do they go?
Thanks!
DC - That was indeed why I was asking. I'm busily SPICEing a few variants of the buffer at the moment, using this as a starting point. Ive a built f6 here in front of me but the jfets are not at all well matched, so my thought is to retro fit the diamond buffer and use the jfets elsewhere... 🙂
Another question if i may? Theres a couple of 'extra' caps on the pcb around the diamond that aren't on the schematic. Before I trace them through, what are they for/ where do they go?
Having finished F-6 in the Deluxe 4U chassis, I can tell all that it is more than adequate for this amplifier. At standard bias, it is just warm. Going higher it is still good.
It is indeed smaller than the 5U I built BA-3 in and I wondered, but F-6 does not appear to be as hot as some Pass amps. While considerably smaller that 5U, it is just fine, not borderline, but fine.
I think I will build M-2 in a 4U as well.
http://www.diyaudio.com/forums/pass-labs/277850-f6-illustrated-build-guide-6.html#post4600106
Russellc
Sorry if this has been asked before, but can I use the F6 as monoblocks for more power, I'd like to drive my quad ESL63 with them.
F6 as monoblockes
Hii to all' I'd like to know if I can run the F6 as monoblock for more power, in order to drive my QUAD ESL63?
Hii to all' I'd like to know if I can run the F6 as monoblock for more power, in order to drive my QUAD ESL63?
yes
I believe that question was asked already , and already replied to
most probably even with adequate schematic , with necessary changes
I believe that question was asked already , and already replied to
most probably even with adequate schematic , with necessary changes
nope , but I can draw it (if I already didn't and posted somewhere in the thread )
what sort of power you're expecting ?
what sort of power you're expecting ?