Class D Amp with LM566, LM393 and 2XIRF530

[PetruV]

Please tell me the pcb sizes for d200

 

[PetruV]

No, ifound the dimensions there 52.5mm 120mm

 

[PetruV]

I have printed the pcb and theire correct size but i have to go to an laser printer
Here is the file,if you print it full page photo without fit picture to frame it will work,this will help many people

 

[PetruV]

Thanks to all for your help,now i going to someone with a laser printer and build this thing,but does it work at +-25v for a test

 

[Tekko]

You will need to size the Vreg resistors for the rail voltage used.

 

[PetruV]

then im not going to test it at 25v,im going t jump directly to building a smps for about 80v since i thought 90 is to much and too many modifications have to be done

 

[Tekko]

But put a light bulb in series with the mains in so that u dont end up with a charred amp and a charred smps if all goes wrong.

 

[PetruV]

But put a light bulb in series with the mains in so that u dont end up with a charred amp and a charred smps if all goes wrong.

I have been always doing this with mains powered device,but i didnt think it will work with a smps

 

[Tekko]

It works with all mains powered devices, if the amp draws excessive current, the mains voltage at the smps will drop and possibly activate the uvlo of its pwm controller, but if the amp is fine, the bulb will be dim or completely off, just as it would with a linear psu.

 

[PetruV]

It works with all mains powered devices, if the amp draws excessive current, the mains voltage at the smps will drop and possibly activate the uvlo of its pwm controller, but if the amp is fine, the bulb will be dim or completely off, just as it would with a linear psu.

interesting, i have found the ir2153 chip and a lot of people are using it for smpsus,just hae to find the right schematic

 

[apexaudio]

interesting, i have found the ir2153 chip and a lot of people are using it for smpsus,just hae to find the right schematic

Use schematic from post #10 in this thread with 2 ATX transformers without rewinding.

 

[PetruV]

Use schematic from post #10 in this thread with 2 ATX transformers without rewinding.

Thats only 50v,how can i up the voltage,but thanks anyways

 

[de Ocampo]

sir abetir, for pcb etching in any weather, i'm diluting with Clorox the ferric chloride for faster process.
regards,
freestyle

Thank you for the tip Freestyle, 😉

 

[norazmi]

Here's my D200v2 build, it still needs a few parts to make it complete....🙂

make some space for heatsink to be mount at mosfet.

p/s - i did run +- 45 vdc for irf540N no problem with full discrete ucd version.

 

[PetruV]

Pcb,only 1 chanell the other is so bad its not even worth trying,is this good for etching,looks pretty good for my first pcb ever,


Do you think its good enough or should i get another one,for the other chanell im obviosely goinf to get a new one

 

[PetruV]

smAll update: there were some misakes but they all have been repaired,tomorow i will be etching.

I have set a deadline for this project 6 june 2013,untill the i hope to have it done and working.If i dont have it built until then no big deal,its not an actual deadline,its just i time i have set for myself to motivate me

 

[Tekko]

Bleh! Looks like KRAP! sorry.

 

[PetruV]

Bleh! Looks like KRAP! sorry.

It was done on a copy machine,on smooth paper,and as my first pcb and amp ever,i will try and etch it tomorow

 

[de Ocampo]

make some space for heatsink to be mount at mosfet.
p/s - i did run +- 45 vdc for irf540N no problem with full discrete ucd version.

H! Azmi,
Good to see you back..🙂 The Fets will be mounted under the board, I have here an old flat heatsink used for TO-3 outputs. I'll have to cut it though coz it's huge....😀

Regards!

 

[PetruV]

No wtching,they are tooo bad and im going to clean them and try it again