The volt+ might measure better, might measure worse.
Exactly.
alkasar reacted to posters preferring the volt+ and asked: does it measure the same or better?
I reacted: or worse?
Automatic assumption: people will prefer better.
Kingrex Tripath is an example of worse performing Tripath-design, audiophiles prefer. Most other Tripath designs are better.
Because this thread is about tpa3116/18 I mentioned the poor chinese tube amps posters prefer, best in front of worst tpa3116/18 double chip ampboard posters prefer, into Fostex or Lowther speakers, remember audio is all about synergy, making the right combinations, posters prefer.
Posters will swear this is the audiophile dream combination. It beats or equals $$$$$ expensive audiophile tube based systems.
You can't measure audiophiles, you cannot make assumptions about them.
The volt+ might measure better, might measure worse.
Thanks for clearing up.
Only using Kingrex PSU these days which is the best I have.
In exchange for a review CDGAMES sent me the Allo Volt+ amp. I received it a few days ago. I already told CDGAMES that I cannot write a technical review because I am not a technical person. What I can write is my personal experience with the Volt+ amp.
A few years ago I discovered the Class D amp. I bought a Tripath amp (2021 Indeed Hifi) for my study room and I liked it. After reading many pages in audioforums I bought a SMSL SA-60 amp (TPA3116). I liked it much more than my Tripath amp and I gave the Tripath amp to a friend.
After a few months I exchanged the laptop power supply for a linear power supply (Delta Elektronica M24-12HE. In the Netherlands, where I live, they are not as expensive as on ebay).
The 24V linear power supply had a big impact on the sound. In my opinion everything was better.
After enjoying the SMSL/Delta combination for a year or so, I read about the TPA3118 Sanwu monoboards. I ordered two, connected them (unmodded) with the Delta Elektronika PS and the Iqaudio Dac and I couldn’t stop listening. It was so captivating. I listened to this combination for half a year.
Then I read about the Volt+. CDGAMES sent me one. The board is quite heavy and soldering is good. I started to listen together with a friend (who has a technical background). We connected the Volt+ to the Delta Elektronika PS and the Raspberry Pi Zero/ IQaudio (we used three batteries, 5V, 5V, 3,3V) and my B&W DM5 speaker. We started to listen.
We listened to:
-Nathalie Merchant
-Tracy Chapman
-Lucy Ward
-Youn Sun Nah – Album: Lento
-Steven Bernstein – Album: Diaspora Soul
It was ok. There was no hiss when we paused the music. The sound was detailed, powerful, stereo-image was ok, middle notes were ok. But the high and low notes were not very good, muddy, and female voices were not captivating. Don’t understand me wrong, it was not bad, but it was, in our opinion, worse than the Sanwu monoboards. It was not very musical. After half an hour we wanted to stop listening.
Then I thought: Well the Volt+ has a Capacitance Multiplier so may be it’s a good idea to exchange the Delta Elektronika 24V Linear PS for a laptop PS. That’s what I did and what a difference it made! We listened the same songs and more and more. How does this song sound on the Volt+? And this song? Female voices were terrific.
In our opinion, the laptop PSU made the Volt+ better in every way. I will try to describe the sound, realizing it’s very difficult and subjective to describe a sound in words!
There is space between the instruments. It’s not muddy or woolly. It’s transparent. The high notes are clean. 3D imaging is good. Beautiful bass. The sound is quiet (probably the wrong word in English) and in control. The sound is detailed (not too much, exactly good) and dynamic.
We listened to Youn Sun Nah (Empty Dream from the album Lento) and it was breath-taking! Never heard it so! We listened to Steven Bernstein (L’Chaim from the album Diaspora Soul – it is one of my favourite albums). Perfect, completely in control, detailed, dynamic. We listened to the new Leonard Cohen single Want it darker (the only song we listened on Spotify). We never heard it more beautiful!
At the end of our listening session we gave marks:
Sanwu monoboards (unmodded) with 24V Linear PS – 7,5 (on a scale from 1-10)
Volt+ with 24V Linear PS – 6,5 (on a scale from 1-10)
Volt+ with 19V laptop PS – 9,0 (on a scale from 1-10)
We listened much more than we planned. And to summarize my/our experience: This is a very musical Amp. That my friend also wants to buy one says enough….
An addition to my review: I turned the trimmer pot and the voltage dropped to 22.5 Volt. The sound was better, less muddy, more lively but ... not as good as the 19V laptop powersupply. I think 19V is de optimal voltage for the Volt+ amplifier. The sound is imho very good.
Hello everyone ,
thx you very much for your kind words on the Volt+
I want to announce that next week we will release a 24 stepped attenuator made with 0.1% thin film (audio grade) resistors. (of course 10k potentimeter)
It will improve your Volt+ further.
I have attached the prototype pics, mass production will start next week.
thx you very much for your kind words on the Volt+
I want to announce that next week we will release a 24 stepped attenuator made with 0.1% thin film (audio grade) resistors. (of course 10k potentimeter)
It will improve your Volt+ further.
I have attached the prototype pics, mass production will start next week.
Attachments
An addition to my review: I turned the trimmer pot and the voltage dropped to 22.5 Volt. The sound was better, less muddy, more lively but ... not as good as the 19V laptop powersupply. I think 19V is de optimal voltage for the Volt+ amplifier. The sound is imho very good.
What 19V power supply do you have?
Brand?
What's an audio grade resistor?
Beside this, if this is an audio potentiometer, where is the shield?
Beside this, if this is an audio potentiometer, where is the shield?
Last edited:
Thanks for the commercial.
Any measurement available on this Volt+ amp ?
We will have some measurements public on the webpage next week. (ap machine test)
What's an audio grade resistor?
Beside this, if this is an audio potentiometer, where is the shield?
We chose the resistors to have low noise.
What 19V power supply do you have?
Brand?
I use an Asus Laptop PSU 19V 3.42A
ASUS 19V 3.42A Laptop Adapter 19V 3.42A,65W,Vervangende Laptop Adapters voor ASUS19V 3.42A | batterij-pc.nl
thanks.We will have some measurements public on the webpage next week. (ap machine test)
please leave a link. Google search get's crazy with names as common as cd, games and volt 😀
Has anyone tried running the Sanwu TPA3118 mono boards with input transformers?
What is the proper way to wire it up?
What is the proper way to wire it up?
Is the quality of the C connected to pin 5 important if the board is SE pbtl?
I wonder if this would be an easy mod to the sanwu 3118 without too much smd-fiddling:
-remove C41 and put a bridge in its place
-connect a quality film cap to the 'input-hole'
-leave C21 as it is
I wonder if this would be an easy mod to the sanwu 3118 without too much smd-fiddling:
-remove C41 and put a bridge in its place
-connect a quality film cap to the 'input-hole'
-leave C21 as it is
We will have some measurements public on the webpage next week. (ap machine test)
Any news on this?


Any news on this?![]()
As a buyer I sent a message to support also asking about meusurements.
But since this is an DIY thread I hope they stop promote it here even if I
hype it.
Vendor Forums maybe is better for them as Buffalo DAC who moved there.
🙂
Thanks, what exactly did you measured with the frequency response? The whole report is kinda "less usefull". 😉
- Home
- Amplifiers
- Class D
- Cheap TPA3118D2 boards, modding them and everything that comes with it