900W H-class PA Amp with Limiter

[rohin]

this modification is old as this thread and b500
but nobody share pcb after all of triple ef
hope you make it this time[/QUOTE]
pcb share by liem poo is not that tef version.can this tef with 8 pair can handle 2 ohm load?

 

[juanete]

ye ápex its a idea but all the tehnlogie has been created by ideas ,and this huge amplifier should work, who could made the PCB of this low power amplifier Project 117 😀

 

[buby]

Poštovani g.Mile, dali možete reći kolika je snaga r.m.s na 8ohm pojačala BA2000 i dali je to najjača verzija vašeg pojačala?
Pozdrav Zoran



English please.


Dear G.MI , if you can tell how much power rms at 8ohm amplifier BA2000 and whether it is the most powerful version of your amp ?
Hi Zoran

 

[apexaudio]

Poštovani g.Mile, dali možete reći kolika je snaga r.m.s na 8ohm pojačala BA2000 i dali je to najjača verzija vašeg pojačala?
Pozdrav Zoran



English please.


Dear G.MI , if you can tell how much power rms at 8ohm amplifier BA2000 and whether it is the most powerful version of your amp ?
Hi Zoran

1000W/8R, VERTEX is my most powerful amp,
Regards

 

[souwel]

Which is true sir mile according to your suggestions. between the direction of the diode schematic and layout protect that I circled in red color?

An externally hosted image should be here but it was not working when we last tested it.

 

[souwel]

protect H900

Which is true sir mile according to your suggestions. between the direction of the diode schematic and layout protect that I circled in red color?

An externally hosted image should be here but it was not working when we last tested it.

 

[souwel]

An externally hosted image should be here but it was not working when we last tested it.

 

[suryadi5417]

H900 MODIFICATION...

Litle modification again.... not conecting yet.... perhaps tomorow.

REGADS

 

[apexaudio]

Which is true sir mile according to your suggestions. between the direction of the diode schematic and layout protect that I circled in red color?

Schematic is corect, diode polarity is wrong (reverted) on pcb.

 

[apexaudio]

Litle modification again.... not conecting yet.... perhaps tomorow.

REGADS

Nice work,
Regards

 

[souwel]

Schematic is corect, diode polarity is wrong (reverted) on pcb.

accepted the love sir mile on your fast reply ..

regards

 

[engel dela pena]

😀😀hmmmm so many large picture so far

 

[Techpolice]

Amp based on B600

hi sir mile.pls check my schema sir if there something wrong.
coz can't continue my pcb if there's a mistake.

 

[Techpolice]

pls check my schem

hi sir miles and sir angel.
pls check my schema coz i can't proceed if there's something wrong.

 

[Techpolice]

sir engel is this right or wrong?

 

[engel dela pena]

sir engel is this right or wrong?

can you make two separate board
output
driver
😀

 

[engel dela pena]

sir wil,
can I have this pcb,pdf file?

 

[44250]

print it "as it is",you should get it in right dimensions.

 

[wiljj78]

sir wil,
can I have this pcb,pdf file?

 

[Techpolice]

can you make two separate board
output
driver
😀

how about the stepper sir?should i put it on the driver board or in the output?