PCB in cdr format
Hello mile sir
I want to start building my first amp with AX14
if you do not mind please send me a file with cdr format, because I also use corel draw.🙂
my email is cakracom@att.net
sorry for my english
Hello mile sir
I want to start building my first amp with AX14
if you do not mind please send me a file with cdr format, because I also use corel draw.🙂
my email is cakracom@att.net
sorry for my english
Thanks Mr MILE previously.
I have a little problem about the transformer, with specification 5 Amp 30 Volt CT.
I've made PCB Power Supply type F100.
the question whether there are components thatmust to be replaced if I use 30V voltage CT ?
if I replace the 0.1 ohm to 0.5 ohm 5 W what happened?
and 1K2 to 1K5 5 W what also happens?
Please help Mr. Mile
Mas. ga usah pake format lain. udah aja pake Microsoft World. gambar PCB di Drag ke World aja. ukurannya langsung pas ko mas. kalo belum yakin tinggal di klik kanan pilih Size. dan jangan lupa Gambar harus di Setting Miror atau terbalik Hurufnya. Semoga Membantu
5Aac and 30Vac centre tapped is 150VA.
What amplifier and speaker are you expecting to drive?
Andrew thank you greetings. My question in addressed to Mr. Miles, because I'm building the power supply made by APEX-type F100. original circuit uses transformer 42VAC secondary. The problem is I do not have a transformer with a 42VAC secondary.
I have a 5 Ampere Transformer 30VAC
The question is whether there are components thatmust to be replaced for this circuit works maximal
Attachments
hai all. if i using capacitor 10000uf/100V.what maximum voltage supply to make this capacitor work very well?
Replace 0.1R/5W with 0.22R/5W and 1k2/5W with 680R/5W for 5A 30V CT transformer.
Regards
Hello Mile sir, I have some questions
Q1-Q2 can be replaced with 2SA798?
I have a transformer with 32V 5A AC output voltage, what is the power that I get from the circuit AX14?
Q1-Q2 can be replaced with 2SA798?
I have a transformer with 32V 5A AC output voltage, what is the power that I get from the circuit AX14?
saya pingin belajar menggambar lay out dengan corel draw mas,..makanya saya minta dikirimi file aslinya dari Mister Mile untuk contoh 😀
Gentlemen, this is an English language forum- please see our forum rules.
Yes, you can use dual transistor instead Q1, Q2. With 2X32V 5A AC power you get will be 60W/8R, 100W/4R.
ax14
hi apexaudio
greetings can vas stage of ax14 and a triple darlington output stage
be used for more power with 10 output pairs what would be power output of amp at 80 volt dc rails be is it possible
thanking you
andrew lebon
hi apexaudio
greetings can vas stage of ax14 and a triple darlington output stage
be used for more power with 10 output pairs what would be power output of amp at 80 volt dc rails be is it possible
thanking you
andrew lebon
Hello sir mile
thank you, finally I finished with my AX14, sounds quite satisfactory results. and I have a plan to replace my TDA7294 with AX14.
if I want to make the AX14 as a sub amp is there anything that needs to be changed at the input section , in addition to the existing sub filter?
Regards Chakra 🙂
thank you, finally I finished with my AX14, sounds quite satisfactory results. and I have a plan to replace my TDA7294 with AX14.
if I want to make the AX14 as a sub amp is there anything that needs to be changed at the input section , in addition to the existing sub filter?
Regards Chakra 🙂