Vertex Amp By apexaudio

[wattaniya]

any subtitude for her156 diode.

 

[blueice23]

blue ice,
amp is already working,limiter also working
picture on page 1 post#1 is working unit
page 1 post #7 the green 1 is updated pcb
if anyone want to help upgrade pcb is much welcome since driver transistor need to be mounted on main heatsink,we are in need of pcb expert like sir COOLET.
but amp is working and stable with measurement already post and with speaker load test by sir jay

Thanks Engel!

I'm currently looking for a place where to get the IR2117. It has been my ongoing problem since the H900 was posted. Hope you can direct me where I can purchase this one. Thanks again!

Blueice23

 

[ChingTan]

Thanks Engel!

I'm currently looking for a place where to get the IR2117. It has been my ongoing problem since the H900 was posted. Hope you can direct me where I can purchase this one. Thanks again!

Blueice23

you can try to ask the ts maybe he can sell you if he have spare

 

[wattaniya]

hi apex sir,
can i use mur 160 instead bav21 and her156?

 

[engel dela pena]

can you please tell your location,
i also have that problem before,we can contact some good guys but it is better if we do in group to lessen lbc,jrs fee
please email me
engel9mcnaly@yahoo.com

 

[irvynejay]

limiter with balance input

untested new board of limiter balance input and opa limiter is tested on separate board

 

[irvynejay]

limiter with balance input/opa and filter 30-50hz untested

for diy

 

[andrewlebon]

LIMITER

hi irynejay
greetings just want to know why you didnt use first ic tlo72
hows qsc 4050 clone going
warm regards
andrew

 

[NMOS]

hi irynejay
greetings just want to know why you didnt use first ic tlo72
hows qsc 4050 clone going
warm regards
andrew

LM13600n in your picture is obsolete

 

[NMOS]

for diy

where to get LM13600...its obsolete


but LM13700 is available is it possibile for replacement ?

 

[irvynejay]

lm13600

Yes NMOS 13700 can be use
Here is my limiter the 2nd and 3rd picture not yet tested with balance input /opa limiter and sub filter 30=50 hz


@andrewlebon 1st ic is for balance input you may or may not use it if you don't have balance input pls see reference in PDF
about 4050 im getting very slow on that project will keep you inform

 

[irvynejay]

vertex with limiter

new limiter balance/opa filter board now working on vertex

 

[Thabto]

Hi, I need to etch this amp asap. Please give me the accurate final PCB and layouts. What transformer are using on this amp? Thanks.

 

[engel dela pena]

see post no.7
see post no.72

 

[irvynejay]

Vertex With MJL

Vertex now Powered on MJL21193/94 IRF3710x6 Mur20200ct

its has big deference ,,it has more power details audio and first power tump is gone..

Measurement will be display later

 

[andrewlebon]

nice work

Hi irvynejay
greetings nice work its time to power vertex on been lazy
warmregards
andrew

 

[irvynejay]

2 channel vertex amp both have MJL's

Ready to fire up Twin Vertex

 

[pawan borkute]

dear sir
i like this pcb so i want amp & stepdriver pcblayout please send me the hole project my id(pb_sound@rediff.com).


thanks @ regard

 

[irvynejay]

2 channel power up loade 4R each channel

final vertex 2 channel fired up

 

[ravpreet420]

share some measurements