Ultra-high performance, yet rather simple - hybrid and more!

Success!!

DC offset is just a few mV!

Background noise is only audible very close to the speaker. Sounds great!

Thanks for your help!

Now I know I can build the second one and figure out the hard stuff. Switches, connectors, chassis final details, etc.
 
Things left to iron out en route to a complete amp:
  • Install speaker DC protection board
  • Add IEC inlet plus switch and fuse
  • Add safety earth connection from PSU to a point on the chassis frame or heat sink
  • Add a switch and chassis connector for the separate 12vdc SMPS that powers the 12au7 heater (I was hoping to use the aux supply on the big smps, but that introduced more hum on the output before)
  • Cut and install lexan panels

That will take a while... :snail:
 
I have DC protect boards from xrk’s Etsy shop. I was planning to just use separate switches for the separate heater and amp smps (switch on the tube heater, wait a minute, then switch on the amp).

I’ll take a look again at the smart control boards...
 
The amp control boards actually came about for starting and protecting this amplifier. It would be a good choice here, and save a bit of chassis work. No need for extra switching and fusing, just a small push button and LED on the front. Also after the amplifier is started there needs to be a delay to let the tube stabilize before DC offset settles out enough not to trigger a normal DC detection circuit.

Amp Control System 6 V2.3 Boards Bundle (5 PCBs, Simpelstark family) – Virtual Zero Audio Store
 
Last edited:
My SSR protection boards work fine. Perfectly if the tube is already warm.

It also works from cold power on of both the amp and tube smps at the same time.

The DC sensing works just fine in my application. The SSR light goes on briefly after the initial delay, then shuts off quickly as the DC offset rises, then goes back on after DC goes back down. My DMM didn’t read any more than 350mV the whole time.

DC went to 1.5V for an instant after power off.

I think I’ll still incorporate a switch for the tube smps just to be safe.
 
Last edited:
Two TubSuMo monoblocks are operational!

There is some background noise, but not noticeable away from nearfield.

They’re playing through my test speakers well now. DC offset servos are working perfectly.

I’ll try them out in my main rig tomorrow. Then I’ll affix some lexan panels and figure out the hardest part: final chassis details (mounting connectors, IEC socket, switches, etc.).

This open frame makerbeam build has been fun.
 

Attachments

  • 3800DDAE-6197-4A9F-8ED0-16F62B3DC69F.jpg
    3800DDAE-6197-4A9F-8ED0-16F62B3DC69F.jpg
    1,007.5 KB · Views: 678
Mad science audio is alive!!! 😀

The noise from my test rig is totally gone!

They sound quite good.

Happy birthday to me. :yes:
 

Attachments

  • A77E0B95-8BF9-4A7A-98D8-CCB0BC254503.jpg
    A77E0B95-8BF9-4A7A-98D8-CCB0BC254503.jpg
    981.2 KB · Views: 659
  • 4ADEBB94-5BED-4123-8D2E-F230565F391B.jpg
    4ADEBB94-5BED-4123-8D2E-F230565F391B.jpg
    949 KB · Views: 610
I’ve been running my TubSuMo mono amps every day, with nightly louder sessions. They have exceptional sound quality and finesse. It’s a tossup in level of enjoyment between these and my updated Hafler DH-220C amp. These are certainly prettier. 😀

Thanks again to Valery and jwilhelm for the design and help, and to Evan for building the boards and sinks well (and selling them to me)!

‘The lottery’ is commanding a lot of attention on the forum—and rightfully so—but any potential builders should look into vzaudio projects for top-notch amplifier options. Great design, support, and results!