Hi diyiggy,
some component values have been changed to better set the current flowing with no load, so please use the last BOM and use BC550/BC560 if you have them in stock.
I have bought some 2SK170 from Banzai Music, it looks like they are genuine.
Andrea
some component values have been changed to better set the current flowing with no load, so please use the last BOM and use BC550/BC560 if you have them in stock.
I have bought some 2SK170 from Banzai Music, it looks like they are genuine.
Andrea
Thanks Andrea, I will. I have purchased as well some 560 from them but dunno if Fairchild... I don't think they are, it was for a non critical app.
On my modest side I had few exchanges with the great Pedja Rogic in some public posts on his blog but also some PM with the idea in mind to go a little further with the AYA (5 edition rightnow is with discret I/V and it occurs it will relaunch also in september his USB to sim board for the TDA1541A with DIL 14 vias for third party crystals I asked like the squarer board.
The AYA 5 will also have the USB to sim board embeded but with uf-l socket input for third party clocks. Maybe a squarer to UFL or the former DIscroll with a ufl-outputt adaptaot worths it, I don't know, with the idea to use no longer than 2" uf-l wires perhaps?!
He was nice again for us DIY people, he is a very open minded guy, and both of your designs together should works great 🙂 😎
. My final will be with a -E188CC- I/V from Thorsten Loesch ECC88/6DJ8 design !
Houps, I almost need a prior carpet, lol 😀, but many thanks guys 🙂
On my modest side I had few exchanges with the great Pedja Rogic in some public posts on his blog but also some PM with the idea in mind to go a little further with the AYA (5 edition rightnow is with discret I/V and it occurs it will relaunch also in september his USB to sim board for the TDA1541A with DIL 14 vias for third party crystals I asked like the squarer board.
The AYA 5 will also have the USB to sim board embeded but with uf-l socket input for third party clocks. Maybe a squarer to UFL or the former DIscroll with a ufl-outputt adaptaot worths it, I don't know, with the idea to use no longer than 2" uf-l wires perhaps?!
He was nice again for us DIY people, he is a very open minded guy, and both of your designs together should works great 🙂 😎
. My final will be with a -E188CC- I/V from Thorsten Loesch ECC88/6DJ8 design ! Houps, I almost need a prior carpet, lol 😀, but many thanks guys 🙂
Last edited:
Hi Andrea,
Please point me to where I can find the manual for the TWSAFB-RPI-F power supply. I need to order the power transformer for it. I couldn't find it
Thanks
Please point me to where I can find the manual for the TWSAFB-RPI-F power supply. I need to order the power transformer for it. I couldn't find it
Thanks
Hi Andrea,
I was able to power up the twrps-ugl using the specified transformer and im getting output of about 26vdc.. measured secondary of the power trans and it read 24vac.. measured my wall outlet and it was at 125vac.. im going to power the drixo clocks with this.. is 26vdc too high?
Can i use the center tap of 12v for the twrps-ugl? The manual states input of 18-20vac.
Thanks
I was able to power up the twrps-ugl using the specified transformer and im getting output of about 26vdc.. measured secondary of the power trans and it read 24vac.. measured my wall outlet and it was at 125vac.. im going to power the drixo clocks with this.. is 26vdc too high?
Can i use the center tap of 12v for the twrps-ugl? The manual states input of 18-20vac.
Thanks
Last edited:
26vdc is too high for the DRIXO.
If you are reading 26vdc at the output connectors of the TWRPS-UGL there is something wrong, the regulator is not working, the output voltage should be around 15vdc.
Please, check the soldering.
If you are reading 26vdc at the output connectors of the TWRPS-UGL there is something wrong, the regulator is not working, the output voltage should be around 15vdc.
Please, check the soldering.
Hi Andrea,
Thanks for the reply. I didn’t assemble the power supply. I bought it finished. Im not sure where to start on diagnosing it
Thanks for the reply. I didn’t assemble the power supply. I bought it finished. Im not sure where to start on diagnosing it
Hi Andrea,
Do you still have a completed finished TWRPS-UGL board available for sale? I haven’t diagnosed my board yet but planning on buying another one instead. Im not very good with smd soldering anyway. Would be much easier for me to get a new one.
By the way, i am now playing the drixos in my ianfifo setup and it is just amazing. Currently just powering them with ifi power x power supply.. i bet it will be even better with better power supply. The drixos just blows away the crystek and accusilicons..
Do you still have a completed finished TWRPS-UGL board available for sale? I haven’t diagnosed my board yet but planning on buying another one instead. Im not very good with smd soldering anyway. Would be much easier for me to get a new one.
By the way, i am now playing the drixos in my ianfifo setup and it is just amazing. Currently just powering them with ifi power x power supply.. i bet it will be even better with better power supply. The drixos just blows away the crystek and accusilicons..
Unfortunately I have no board left from the last GB.
You could send me your board back so I should try to repair it.
You could send me your board back so I should try to repair it.