You can use a multimeter. It won't tell you much but it may show if the drive signal is really bad.
P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 9:15 pm #21 2019-12-05 9:15 pm #21 You can use a multimeter. It won't tell you much but it may show if the drive signal is really bad. ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 9:18 pm #22 2019-12-05 9:18 pm #22 Should i set the meter on AC volts or DC volts ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 9:18 pm #23 2019-12-05 9:18 pm #23 And what should i specifically be looking for if anything ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 9:21 pm #24 2019-12-05 9:21 pm #24 Post the DC voltage you read on each bank. ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 9:31 pm #25 2019-12-05 9:31 pm #25 One bank shows 0v dc and other shows 7.91v dc ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 9:36 pm #26 2019-12-05 9:36 pm #26 Does this change if you connect a load to the speaker terminals? ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 9:44 pm #27 2019-12-05 9:44 pm #27 Yes it jumped up to 9v other stayed the same ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 9:49 pm #28 2019-12-05 9:49 pm #28 Was the black meter probe on the source leg of the FET and the red on the gate of the same FET? ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 9:50 pm #29 2019-12-05 9:50 pm #29 Yes ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 9:54 pm #30 2019-12-05 9:54 pm #30 I put black probe on pin 3(source) and red probe on pin 1 (gate) ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 9:55 pm #31 2019-12-05 9:55 pm #31 What's the DC voltage across the drivers (Q12/14)? Black on Q14 collector. Red on Q12 collector. ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:01 pm #32 2019-12-05 10:01 pm #32 I dont see Q12/14 ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:02 pm #33 2019-12-05 10:02 pm #33 I only see drivers Q287/286 and Q285/284 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 10:09 pm #34 2019-12-05 10:09 pm #34 Whatever they are equivalent to Q12/14 on the SLA diagram. ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:20 pm #35 2019-12-05 10:20 pm #35 Sorry but i dont understand ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:21 pm #36 2019-12-05 10:21 pm #36 Whats the SLA diagram ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 10:29 pm #37 2019-12-05 10:29 pm #37 My mistake. The AQ1200 diagram I posted. The drivers are Q284/285. ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:46 pm #38 2019-12-05 10:46 pm #38 Ok will check those later as its 1 am here this side of the world thanks a lot for the help so far much appreciated ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-06 6:06 pm #39 2019-12-06 6:06 pm #39 Hi should i check the voltage from collector to emitter ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-06 6:13 pm #40 2019-12-06 6:13 pm #40 Collector to collector. ••• More options Share Prev 1 2 3 4 5 Next First Prev 2 of 5 Go to page Go Next Last Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link Home General Interest Car Audio Targa 2.8kz staying in protection Top Bottom
A Aqeeb127 Member Joined 2018 2019-12-05 9:18 pm #22 2019-12-05 9:18 pm #22 Should i set the meter on AC volts or DC volts ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 9:18 pm #23 2019-12-05 9:18 pm #23 And what should i specifically be looking for if anything ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 9:21 pm #24 2019-12-05 9:21 pm #24 Post the DC voltage you read on each bank. ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 9:31 pm #25 2019-12-05 9:31 pm #25 One bank shows 0v dc and other shows 7.91v dc ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 9:36 pm #26 2019-12-05 9:36 pm #26 Does this change if you connect a load to the speaker terminals? ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 9:44 pm #27 2019-12-05 9:44 pm #27 Yes it jumped up to 9v other stayed the same ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 9:49 pm #28 2019-12-05 9:49 pm #28 Was the black meter probe on the source leg of the FET and the red on the gate of the same FET? ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 9:50 pm #29 2019-12-05 9:50 pm #29 Yes ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 9:54 pm #30 2019-12-05 9:54 pm #30 I put black probe on pin 3(source) and red probe on pin 1 (gate) ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 9:55 pm #31 2019-12-05 9:55 pm #31 What's the DC voltage across the drivers (Q12/14)? Black on Q14 collector. Red on Q12 collector. ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:01 pm #32 2019-12-05 10:01 pm #32 I dont see Q12/14 ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:02 pm #33 2019-12-05 10:02 pm #33 I only see drivers Q287/286 and Q285/284 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 10:09 pm #34 2019-12-05 10:09 pm #34 Whatever they are equivalent to Q12/14 on the SLA diagram. ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:20 pm #35 2019-12-05 10:20 pm #35 Sorry but i dont understand ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:21 pm #36 2019-12-05 10:21 pm #36 Whats the SLA diagram ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 10:29 pm #37 2019-12-05 10:29 pm #37 My mistake. The AQ1200 diagram I posted. The drivers are Q284/285. ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:46 pm #38 2019-12-05 10:46 pm #38 Ok will check those later as its 1 am here this side of the world thanks a lot for the help so far much appreciated ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-06 6:06 pm #39 2019-12-06 6:06 pm #39 Hi should i check the voltage from collector to emitter ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-06 6:13 pm #40 2019-12-06 6:13 pm #40 Collector to collector. ••• More options Share Prev 1 2 3 4 5 Next First Prev 2 of 5 Go to page Go Next Last Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link Home General Interest Car Audio Targa 2.8kz staying in protection Top Bottom
A Aqeeb127 Member Joined 2018 2019-12-05 9:18 pm #23 2019-12-05 9:18 pm #23 And what should i specifically be looking for if anything ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 9:21 pm #24 2019-12-05 9:21 pm #24 Post the DC voltage you read on each bank. ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 9:31 pm #25 2019-12-05 9:31 pm #25 One bank shows 0v dc and other shows 7.91v dc ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 9:36 pm #26 2019-12-05 9:36 pm #26 Does this change if you connect a load to the speaker terminals? ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 9:44 pm #27 2019-12-05 9:44 pm #27 Yes it jumped up to 9v other stayed the same ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 9:49 pm #28 2019-12-05 9:49 pm #28 Was the black meter probe on the source leg of the FET and the red on the gate of the same FET? ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 9:50 pm #29 2019-12-05 9:50 pm #29 Yes ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 9:54 pm #30 2019-12-05 9:54 pm #30 I put black probe on pin 3(source) and red probe on pin 1 (gate) ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 9:55 pm #31 2019-12-05 9:55 pm #31 What's the DC voltage across the drivers (Q12/14)? Black on Q14 collector. Red on Q12 collector. ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:01 pm #32 2019-12-05 10:01 pm #32 I dont see Q12/14 ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:02 pm #33 2019-12-05 10:02 pm #33 I only see drivers Q287/286 and Q285/284 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 10:09 pm #34 2019-12-05 10:09 pm #34 Whatever they are equivalent to Q12/14 on the SLA diagram. ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:20 pm #35 2019-12-05 10:20 pm #35 Sorry but i dont understand ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:21 pm #36 2019-12-05 10:21 pm #36 Whats the SLA diagram ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 10:29 pm #37 2019-12-05 10:29 pm #37 My mistake. The AQ1200 diagram I posted. The drivers are Q284/285. ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:46 pm #38 2019-12-05 10:46 pm #38 Ok will check those later as its 1 am here this side of the world thanks a lot for the help so far much appreciated ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-06 6:06 pm #39 2019-12-06 6:06 pm #39 Hi should i check the voltage from collector to emitter ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-06 6:13 pm #40 2019-12-06 6:13 pm #40 Collector to collector. ••• More options Share Prev 1 2 3 4 5 Next First Prev 2 of 5 Go to page Go Next Last Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link Home General Interest Car Audio Targa 2.8kz staying in protection Top Bottom
P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 9:21 pm #24 2019-12-05 9:21 pm #24 Post the DC voltage you read on each bank. ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 9:31 pm #25 2019-12-05 9:31 pm #25 One bank shows 0v dc and other shows 7.91v dc ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 9:36 pm #26 2019-12-05 9:36 pm #26 Does this change if you connect a load to the speaker terminals? ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 9:44 pm #27 2019-12-05 9:44 pm #27 Yes it jumped up to 9v other stayed the same ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 9:49 pm #28 2019-12-05 9:49 pm #28 Was the black meter probe on the source leg of the FET and the red on the gate of the same FET? ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 9:50 pm #29 2019-12-05 9:50 pm #29 Yes ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 9:54 pm #30 2019-12-05 9:54 pm #30 I put black probe on pin 3(source) and red probe on pin 1 (gate) ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 9:55 pm #31 2019-12-05 9:55 pm #31 What's the DC voltage across the drivers (Q12/14)? Black on Q14 collector. Red on Q12 collector. ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:01 pm #32 2019-12-05 10:01 pm #32 I dont see Q12/14 ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:02 pm #33 2019-12-05 10:02 pm #33 I only see drivers Q287/286 and Q285/284 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 10:09 pm #34 2019-12-05 10:09 pm #34 Whatever they are equivalent to Q12/14 on the SLA diagram. ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:20 pm #35 2019-12-05 10:20 pm #35 Sorry but i dont understand ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:21 pm #36 2019-12-05 10:21 pm #36 Whats the SLA diagram ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 10:29 pm #37 2019-12-05 10:29 pm #37 My mistake. The AQ1200 diagram I posted. The drivers are Q284/285. ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:46 pm #38 2019-12-05 10:46 pm #38 Ok will check those later as its 1 am here this side of the world thanks a lot for the help so far much appreciated ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-06 6:06 pm #39 2019-12-06 6:06 pm #39 Hi should i check the voltage from collector to emitter ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-06 6:13 pm #40 2019-12-06 6:13 pm #40 Collector to collector. ••• More options Share Prev 1 2 3 4 5 Next First Prev 2 of 5 Go to page Go Next Last Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link Home General Interest Car Audio Targa 2.8kz staying in protection Top Bottom
A Aqeeb127 Member Joined 2018 2019-12-05 9:31 pm #25 2019-12-05 9:31 pm #25 One bank shows 0v dc and other shows 7.91v dc ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 9:36 pm #26 2019-12-05 9:36 pm #26 Does this change if you connect a load to the speaker terminals? ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 9:44 pm #27 2019-12-05 9:44 pm #27 Yes it jumped up to 9v other stayed the same ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 9:49 pm #28 2019-12-05 9:49 pm #28 Was the black meter probe on the source leg of the FET and the red on the gate of the same FET? ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 9:50 pm #29 2019-12-05 9:50 pm #29 Yes ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 9:54 pm #30 2019-12-05 9:54 pm #30 I put black probe on pin 3(source) and red probe on pin 1 (gate) ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 9:55 pm #31 2019-12-05 9:55 pm #31 What's the DC voltage across the drivers (Q12/14)? Black on Q14 collector. Red on Q12 collector. ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:01 pm #32 2019-12-05 10:01 pm #32 I dont see Q12/14 ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:02 pm #33 2019-12-05 10:02 pm #33 I only see drivers Q287/286 and Q285/284 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 10:09 pm #34 2019-12-05 10:09 pm #34 Whatever they are equivalent to Q12/14 on the SLA diagram. ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:20 pm #35 2019-12-05 10:20 pm #35 Sorry but i dont understand ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:21 pm #36 2019-12-05 10:21 pm #36 Whats the SLA diagram ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 10:29 pm #37 2019-12-05 10:29 pm #37 My mistake. The AQ1200 diagram I posted. The drivers are Q284/285. ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:46 pm #38 2019-12-05 10:46 pm #38 Ok will check those later as its 1 am here this side of the world thanks a lot for the help so far much appreciated ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-06 6:06 pm #39 2019-12-06 6:06 pm #39 Hi should i check the voltage from collector to emitter ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-06 6:13 pm #40 2019-12-06 6:13 pm #40 Collector to collector. ••• More options Share Prev 1 2 3 4 5 Next First Prev 2 of 5 Go to page Go Next Last Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link Home General Interest Car Audio Targa 2.8kz staying in protection Top Bottom
P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 9:36 pm #26 2019-12-05 9:36 pm #26 Does this change if you connect a load to the speaker terminals? ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 9:44 pm #27 2019-12-05 9:44 pm #27 Yes it jumped up to 9v other stayed the same ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 9:49 pm #28 2019-12-05 9:49 pm #28 Was the black meter probe on the source leg of the FET and the red on the gate of the same FET? ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 9:50 pm #29 2019-12-05 9:50 pm #29 Yes ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 9:54 pm #30 2019-12-05 9:54 pm #30 I put black probe on pin 3(source) and red probe on pin 1 (gate) ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 9:55 pm #31 2019-12-05 9:55 pm #31 What's the DC voltage across the drivers (Q12/14)? Black on Q14 collector. Red on Q12 collector. ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:01 pm #32 2019-12-05 10:01 pm #32 I dont see Q12/14 ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:02 pm #33 2019-12-05 10:02 pm #33 I only see drivers Q287/286 and Q285/284 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 10:09 pm #34 2019-12-05 10:09 pm #34 Whatever they are equivalent to Q12/14 on the SLA diagram. ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:20 pm #35 2019-12-05 10:20 pm #35 Sorry but i dont understand ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:21 pm #36 2019-12-05 10:21 pm #36 Whats the SLA diagram ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 10:29 pm #37 2019-12-05 10:29 pm #37 My mistake. The AQ1200 diagram I posted. The drivers are Q284/285. ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:46 pm #38 2019-12-05 10:46 pm #38 Ok will check those later as its 1 am here this side of the world thanks a lot for the help so far much appreciated ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-06 6:06 pm #39 2019-12-06 6:06 pm #39 Hi should i check the voltage from collector to emitter ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-06 6:13 pm #40 2019-12-06 6:13 pm #40 Collector to collector. ••• More options Share Prev 1 2 3 4 5 Next First Prev 2 of 5 Go to page Go Next Last Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link Home General Interest Car Audio Targa 2.8kz staying in protection Top Bottom
A Aqeeb127 Member Joined 2018 2019-12-05 9:44 pm #27 2019-12-05 9:44 pm #27 Yes it jumped up to 9v other stayed the same ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 9:49 pm #28 2019-12-05 9:49 pm #28 Was the black meter probe on the source leg of the FET and the red on the gate of the same FET? ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 9:50 pm #29 2019-12-05 9:50 pm #29 Yes ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 9:54 pm #30 2019-12-05 9:54 pm #30 I put black probe on pin 3(source) and red probe on pin 1 (gate) ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 9:55 pm #31 2019-12-05 9:55 pm #31 What's the DC voltage across the drivers (Q12/14)? Black on Q14 collector. Red on Q12 collector. ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:01 pm #32 2019-12-05 10:01 pm #32 I dont see Q12/14 ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:02 pm #33 2019-12-05 10:02 pm #33 I only see drivers Q287/286 and Q285/284 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 10:09 pm #34 2019-12-05 10:09 pm #34 Whatever they are equivalent to Q12/14 on the SLA diagram. ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:20 pm #35 2019-12-05 10:20 pm #35 Sorry but i dont understand ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:21 pm #36 2019-12-05 10:21 pm #36 Whats the SLA diagram ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 10:29 pm #37 2019-12-05 10:29 pm #37 My mistake. The AQ1200 diagram I posted. The drivers are Q284/285. ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:46 pm #38 2019-12-05 10:46 pm #38 Ok will check those later as its 1 am here this side of the world thanks a lot for the help so far much appreciated ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-06 6:06 pm #39 2019-12-06 6:06 pm #39 Hi should i check the voltage from collector to emitter ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-06 6:13 pm #40 2019-12-06 6:13 pm #40 Collector to collector. ••• More options Share Prev 1 2 3 4 5 Next First Prev 2 of 5 Go to page Go Next Last Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link Home General Interest Car Audio Targa 2.8kz staying in protection Top Bottom
P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 9:49 pm #28 2019-12-05 9:49 pm #28 Was the black meter probe on the source leg of the FET and the red on the gate of the same FET? ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 9:50 pm #29 2019-12-05 9:50 pm #29 Yes ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 9:54 pm #30 2019-12-05 9:54 pm #30 I put black probe on pin 3(source) and red probe on pin 1 (gate) ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 9:55 pm #31 2019-12-05 9:55 pm #31 What's the DC voltage across the drivers (Q12/14)? Black on Q14 collector. Red on Q12 collector. ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:01 pm #32 2019-12-05 10:01 pm #32 I dont see Q12/14 ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:02 pm #33 2019-12-05 10:02 pm #33 I only see drivers Q287/286 and Q285/284 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 10:09 pm #34 2019-12-05 10:09 pm #34 Whatever they are equivalent to Q12/14 on the SLA diagram. ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:20 pm #35 2019-12-05 10:20 pm #35 Sorry but i dont understand ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:21 pm #36 2019-12-05 10:21 pm #36 Whats the SLA diagram ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 10:29 pm #37 2019-12-05 10:29 pm #37 My mistake. The AQ1200 diagram I posted. The drivers are Q284/285. ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:46 pm #38 2019-12-05 10:46 pm #38 Ok will check those later as its 1 am here this side of the world thanks a lot for the help so far much appreciated ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-06 6:06 pm #39 2019-12-06 6:06 pm #39 Hi should i check the voltage from collector to emitter ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-06 6:13 pm #40 2019-12-06 6:13 pm #40 Collector to collector. ••• More options Share Prev 1 2 3 4 5 Next First Prev 2 of 5 Go to page Go Next Last Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link Home General Interest Car Audio Targa 2.8kz staying in protection Top Bottom
A Aqeeb127 Member Joined 2018 2019-12-05 9:50 pm #29 2019-12-05 9:50 pm #29 Yes ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 9:54 pm #30 2019-12-05 9:54 pm #30 I put black probe on pin 3(source) and red probe on pin 1 (gate) ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 9:55 pm #31 2019-12-05 9:55 pm #31 What's the DC voltage across the drivers (Q12/14)? Black on Q14 collector. Red on Q12 collector. ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:01 pm #32 2019-12-05 10:01 pm #32 I dont see Q12/14 ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:02 pm #33 2019-12-05 10:02 pm #33 I only see drivers Q287/286 and Q285/284 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 10:09 pm #34 2019-12-05 10:09 pm #34 Whatever they are equivalent to Q12/14 on the SLA diagram. ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:20 pm #35 2019-12-05 10:20 pm #35 Sorry but i dont understand ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:21 pm #36 2019-12-05 10:21 pm #36 Whats the SLA diagram ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 10:29 pm #37 2019-12-05 10:29 pm #37 My mistake. The AQ1200 diagram I posted. The drivers are Q284/285. ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:46 pm #38 2019-12-05 10:46 pm #38 Ok will check those later as its 1 am here this side of the world thanks a lot for the help so far much appreciated ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-06 6:06 pm #39 2019-12-06 6:06 pm #39 Hi should i check the voltage from collector to emitter ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-06 6:13 pm #40 2019-12-06 6:13 pm #40 Collector to collector. ••• More options Share Prev 1 2 3 4 5 Next First Prev 2 of 5 Go to page Go Next Last Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link Home General Interest Car Audio Targa 2.8kz staying in protection Top Bottom
A Aqeeb127 Member Joined 2018 2019-12-05 9:54 pm #30 2019-12-05 9:54 pm #30 I put black probe on pin 3(source) and red probe on pin 1 (gate) ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 9:55 pm #31 2019-12-05 9:55 pm #31 What's the DC voltage across the drivers (Q12/14)? Black on Q14 collector. Red on Q12 collector. ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:01 pm #32 2019-12-05 10:01 pm #32 I dont see Q12/14 ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:02 pm #33 2019-12-05 10:02 pm #33 I only see drivers Q287/286 and Q285/284 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 10:09 pm #34 2019-12-05 10:09 pm #34 Whatever they are equivalent to Q12/14 on the SLA diagram. ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:20 pm #35 2019-12-05 10:20 pm #35 Sorry but i dont understand ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:21 pm #36 2019-12-05 10:21 pm #36 Whats the SLA diagram ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 10:29 pm #37 2019-12-05 10:29 pm #37 My mistake. The AQ1200 diagram I posted. The drivers are Q284/285. ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:46 pm #38 2019-12-05 10:46 pm #38 Ok will check those later as its 1 am here this side of the world thanks a lot for the help so far much appreciated ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-06 6:06 pm #39 2019-12-06 6:06 pm #39 Hi should i check the voltage from collector to emitter ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-06 6:13 pm #40 2019-12-06 6:13 pm #40 Collector to collector. ••• More options Share Prev 1 2 3 4 5 Next First Prev 2 of 5 Go to page Go Next Last Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link Home General Interest Car Audio Targa 2.8kz staying in protection Top Bottom
P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 9:55 pm #31 2019-12-05 9:55 pm #31 What's the DC voltage across the drivers (Q12/14)? Black on Q14 collector. Red on Q12 collector. ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:01 pm #32 2019-12-05 10:01 pm #32 I dont see Q12/14 ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:02 pm #33 2019-12-05 10:02 pm #33 I only see drivers Q287/286 and Q285/284 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 10:09 pm #34 2019-12-05 10:09 pm #34 Whatever they are equivalent to Q12/14 on the SLA diagram. ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:20 pm #35 2019-12-05 10:20 pm #35 Sorry but i dont understand ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:21 pm #36 2019-12-05 10:21 pm #36 Whats the SLA diagram ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 10:29 pm #37 2019-12-05 10:29 pm #37 My mistake. The AQ1200 diagram I posted. The drivers are Q284/285. ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:46 pm #38 2019-12-05 10:46 pm #38 Ok will check those later as its 1 am here this side of the world thanks a lot for the help so far much appreciated ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-06 6:06 pm #39 2019-12-06 6:06 pm #39 Hi should i check the voltage from collector to emitter ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-06 6:13 pm #40 2019-12-06 6:13 pm #40 Collector to collector. ••• More options Share Prev 1 2 3 4 5 Next First Prev 2 of 5 Go to page Go Next Last Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link Home General Interest Car Audio Targa 2.8kz staying in protection Top Bottom
A Aqeeb127 Member Joined 2018 2019-12-05 10:01 pm #32 2019-12-05 10:01 pm #32 I dont see Q12/14 ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:02 pm #33 2019-12-05 10:02 pm #33 I only see drivers Q287/286 and Q285/284 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 10:09 pm #34 2019-12-05 10:09 pm #34 Whatever they are equivalent to Q12/14 on the SLA diagram. ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:20 pm #35 2019-12-05 10:20 pm #35 Sorry but i dont understand ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:21 pm #36 2019-12-05 10:21 pm #36 Whats the SLA diagram ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 10:29 pm #37 2019-12-05 10:29 pm #37 My mistake. The AQ1200 diagram I posted. The drivers are Q284/285. ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:46 pm #38 2019-12-05 10:46 pm #38 Ok will check those later as its 1 am here this side of the world thanks a lot for the help so far much appreciated ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-06 6:06 pm #39 2019-12-06 6:06 pm #39 Hi should i check the voltage from collector to emitter ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-06 6:13 pm #40 2019-12-06 6:13 pm #40 Collector to collector. ••• More options Share Prev 1 2 3 4 5 Next First Prev 2 of 5 Go to page Go Next Last Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link Home General Interest Car Audio Targa 2.8kz staying in protection Top Bottom
A Aqeeb127 Member Joined 2018 2019-12-05 10:02 pm #33 2019-12-05 10:02 pm #33 I only see drivers Q287/286 and Q285/284 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 10:09 pm #34 2019-12-05 10:09 pm #34 Whatever they are equivalent to Q12/14 on the SLA diagram. ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:20 pm #35 2019-12-05 10:20 pm #35 Sorry but i dont understand ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:21 pm #36 2019-12-05 10:21 pm #36 Whats the SLA diagram ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 10:29 pm #37 2019-12-05 10:29 pm #37 My mistake. The AQ1200 diagram I posted. The drivers are Q284/285. ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:46 pm #38 2019-12-05 10:46 pm #38 Ok will check those later as its 1 am here this side of the world thanks a lot for the help so far much appreciated ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-06 6:06 pm #39 2019-12-06 6:06 pm #39 Hi should i check the voltage from collector to emitter ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-06 6:13 pm #40 2019-12-06 6:13 pm #40 Collector to collector. ••• More options Share Prev 1 2 3 4 5 Next First Prev 2 of 5 Go to page Go Next Last Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link Home General Interest Car Audio Targa 2.8kz staying in protection
P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 10:09 pm #34 2019-12-05 10:09 pm #34 Whatever they are equivalent to Q12/14 on the SLA diagram. ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:20 pm #35 2019-12-05 10:20 pm #35 Sorry but i dont understand ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:21 pm #36 2019-12-05 10:21 pm #36 Whats the SLA diagram ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 10:29 pm #37 2019-12-05 10:29 pm #37 My mistake. The AQ1200 diagram I posted. The drivers are Q284/285. ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:46 pm #38 2019-12-05 10:46 pm #38 Ok will check those later as its 1 am here this side of the world thanks a lot for the help so far much appreciated ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-06 6:06 pm #39 2019-12-06 6:06 pm #39 Hi should i check the voltage from collector to emitter ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-06 6:13 pm #40 2019-12-06 6:13 pm #40 Collector to collector. ••• More options Share Prev 1 2 3 4 5 Next First Prev 2 of 5 Go to page Go Next Last Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link Home General Interest Car Audio Targa 2.8kz staying in protection
A Aqeeb127 Member Joined 2018 2019-12-05 10:20 pm #35 2019-12-05 10:20 pm #35 Sorry but i dont understand ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:21 pm #36 2019-12-05 10:21 pm #36 Whats the SLA diagram ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 10:29 pm #37 2019-12-05 10:29 pm #37 My mistake. The AQ1200 diagram I posted. The drivers are Q284/285. ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:46 pm #38 2019-12-05 10:46 pm #38 Ok will check those later as its 1 am here this side of the world thanks a lot for the help so far much appreciated ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-06 6:06 pm #39 2019-12-06 6:06 pm #39 Hi should i check the voltage from collector to emitter ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-06 6:13 pm #40 2019-12-06 6:13 pm #40 Collector to collector. ••• More options Share Prev 1 2 3 4 5 Next First Prev 2 of 5 Go to page Go Next Last Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link
A Aqeeb127 Member Joined 2018 2019-12-05 10:21 pm #36 2019-12-05 10:21 pm #36 Whats the SLA diagram ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 10:29 pm #37 2019-12-05 10:29 pm #37 My mistake. The AQ1200 diagram I posted. The drivers are Q284/285. ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:46 pm #38 2019-12-05 10:46 pm #38 Ok will check those later as its 1 am here this side of the world thanks a lot for the help so far much appreciated ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-06 6:06 pm #39 2019-12-06 6:06 pm #39 Hi should i check the voltage from collector to emitter ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-06 6:13 pm #40 2019-12-06 6:13 pm #40 Collector to collector. ••• More options Share Prev 1 2 3 4 5 Next First Prev 2 of 5 Go to page Go Next Last Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link
P Perry Babin Member Joined 2003 bcae1.com 2019-12-05 10:29 pm #37 2019-12-05 10:29 pm #37 My mistake. The AQ1200 diagram I posted. The drivers are Q284/285. ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-05 10:46 pm #38 2019-12-05 10:46 pm #38 Ok will check those later as its 1 am here this side of the world thanks a lot for the help so far much appreciated ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-06 6:06 pm #39 2019-12-06 6:06 pm #39 Hi should i check the voltage from collector to emitter ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-06 6:13 pm #40 2019-12-06 6:13 pm #40 Collector to collector. ••• More options Share Prev 1 2 3 4 5 Next First Prev 2 of 5 Go to page Go Next Last Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link
A Aqeeb127 Member Joined 2018 2019-12-05 10:46 pm #38 2019-12-05 10:46 pm #38 Ok will check those later as its 1 am here this side of the world thanks a lot for the help so far much appreciated ••• More options Share A Aqeeb127 Member Joined 2018 2019-12-06 6:06 pm #39 2019-12-06 6:06 pm #39 Hi should i check the voltage from collector to emitter ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-06 6:13 pm #40 2019-12-06 6:13 pm #40 Collector to collector. ••• More options Share Prev 1 2 3 4 5 Next First Prev 2 of 5 Go to page Go Next Last Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link
Ok will check those later as its 1 am here this side of the world thanks a lot for the help so far much appreciated
A Aqeeb127 Member Joined 2018 2019-12-06 6:06 pm #39 2019-12-06 6:06 pm #39 Hi should i check the voltage from collector to emitter ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-06 6:13 pm #40 2019-12-06 6:13 pm #40 Collector to collector. ••• More options Share Prev 1 2 3 4 5 Next First Prev 2 of 5 Go to page Go Next Last Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button.
P Perry Babin Member Joined 2003 bcae1.com 2019-12-06 6:13 pm #40 2019-12-06 6:13 pm #40 Collector to collector. ••• More options Share