testing only sorry for the mess
Buffer from Yamaha PA3500
whole
Supply area
2sa2922 transistor
Buffer from Yamaha PA3500

whole

Supply area

2sa2922 transistor

Last edited:
hope you like it sir apex it really kicks although the power supply is not enough for 4 ohms but manageable he he he i'm satisfied i rewond already the transformer to 55-0-55 VAC
and sir kindly advice if it is possible to use 2sa1216 and how so that i can not buy anymore new power trannie's please responds= and thx a lot
regards
and sir kindly advice if it is possible to use 2sa1216 and how so that i can not buy anymore new power trannie's please responds= and thx a lot
regards
@apex sir is it possible to use a PNP trannie to this P.A. and how pls enlighten me sir and i ask something else else is the feedback resistor of this AMP is 22k or 2.2k where can i find it the quality is good but to much med or i mean to much vocals what value of resistor di i change to become lesser meds/vocals
regards...
regards...
Hi radio ,
I have search for you an better schematic , also tested one . I have done small changes for 2SC 5200 as finals ..... I hope you like it .
Regards Alex.
Attached Thumbnails
Attached Files
Nbip300schematic.pdf.pdf (42.1 KB, 119 views)
QUASI 300 BJT N PCB TOP ALL.pdf (151.8 KB, 107 views)
QUASI 300 BJT N PCB TOP VIEW.pdf (46.5 KB, 87 views)
Dear Alex
Can you post me sprint file for Nbip300 pcb layout at my email
rkkatiyar@gmail.com
thanks
katiyar
dear sir,
can you send me also that attached file
at my email khan.shahid251@gmail.com
Last edited:
@ apex VU not working when i provided the supply all led lights up and no visualization comin in from input pls help
regards
regards
@ apex VU not working when i provided the supply all led lights up and no visualization comin in from input pls help
regards
Post pictures of your VU
Hi AudioSenseCD!hope you like it sir apex it really kicks although the power supply is not enough for 4 ohms but manageable he he he i'm satisfied i rewond already the transformer to 55-0-55 VAC
and sir kindly advice if it is possible to use 2sa1216 and how so that i can not buy anymore new power trannie's please responds= and thx a lot
regards

The schematics that you did this amplifier?
thanks
dear apex sir@apex sir as of now i'm goin to etch again and i think i made mistake for printing the PCB
i am also reluctant to draw/etch my own pcb.i hve one uv 8watt tube i exposed it for 30 minutes through negative image on copper clad.after 30 minute i came to know that there was not image .plz let me know how can i get sharp image then i etch that.in anticipating
your ever masood thanking u.
@apex sir is it possible to use a PNP trannie to this P.A. and how pls enlighten me sir and i ask something else else is the feedback resistor of this AMP is 22k or 2.2k where can i find it the quality is good but to much med or i mean to much vocals what value of resistor di i change to become lesser meds/vocals
regards...
Quasi PNP? Feedback resistor is 22k and change it to 2k2 only change gain.
Regards
Quasi PNP? Feedback resistor is 22k and change it to 2k2 only change gain.
Regards
@apex yes sir miles do i have to reverse polarity the diodes and the zener diodes and the pre drivers and vas from pnp to npn and vice versa of their location from mje340=mje350 mje150031=mje150030 location
Last edited:
@apex yes sir miles do i have to reverse polarity the diodes and the zener diodes and the pre drivers and vas from pnp to npn and vice versa of their location from mje340=mje350 mje150031=mje150030 location
Yes, but post your schematic and I will check.
- Home
- Amplifiers
- Solid State
- QUASI Amplifier for Beginners