Hi SORO,
nice led vu meter. but which amp do you use?
QUAD 405
case is made by my design.
Hi friend,Hi apex,
I have attached schematic of tone control_20Hz-20kHz.I want to use 47k pot in place of 10k pot so can you help me to change the RC network value?
thanks
try this preamp schema, I found it from web
Attachments
12dB/oct activ X-over with balanced input and outputs for subwoofer (LO),satelite(HI) or full-range(FR). X-over adjust 50-250Hz, and level for satelite (HI).
Attachments
12dB/oct activ X-over with balanced input and outputs for subwoofer (LO),satelite(HI) or full-range(FR). X-over adjust 50-250Hz, and level for satelite (HI).
sir,
can you post schema and copper side for this project???..
tnx
regards
Appex, thanks for your great circuits! I am going to build this ML3 preamp with ur QUASI amp for my Bass Guitar. In our country buying Hertke,Roland,Fender.... r really expensive as they include 70% govt. tax 🙁 So its a real help for me.
tell me is that volume control with ML3 enough for my setup or I hv to add one log pot to the input of my amp? The 15V power supply needs how much Ampere?
tell me is that volume control with ML3 enough for my setup or I hv to add one log pot to the input of my amp? The 15V power supply needs how much Ampere?
Appex, thanks for your great circuits! I am going to build this ML3 preamp with ur QUASI amp for my Bass Guitar. In our country buying Hertke,Roland,Fender.... r really expensive as they include 70% govt. tax 🙁 So its a real help for me.
tell me is that volume control with ML3 enough for my setup or I hv to add one log pot to the input of my amp? The 15V power supply needs how much Ampere?
In post #35 you have bass guitar amp, ML3 is universal preamp, volume control is enough. Use PSU +/-15V 500mA.
Regards
Is there any problem if I use QAUSI amp? I was planning to make it by two 2N3055 at +/- 30V DC as the circuit seems simple to me.
Thanx.
Thanx.
Is there any problem if I use QAUSI amp? I was planning to make it by two 2N3055 at +/- 30V DC as the circuit seems simple to me.
Thanx.
Quasi amp is clone of some old DYNACORD powered mixer, and no problem at all to use it for instrumental amplifier.
Regards
hello apex
can you give me preamplifier schematic that its output should have at least 300mV with mic in and aux inputs
my mail emmizeb@gmail.com
can you give me preamplifier schematic that its output should have at least 300mV with mic in and aux inputs
my mail emmizeb@gmail.com
hello apex
can you give me preamplifier schematic that its output should have at least 300mV with mic in and aux inputs
my mail emmizeb@gmail.com
Use ML3 from post #1.
Regards
Use ML3 from post #1.
Regards
is this pre amp suits for 600ohms dynamic microphone does it produce any noise
how can i add one more mic and aux?
what will be the output voltage
can i use LM741 instead of TL072
sorry for too many questions
Last edited:
is this pre amp suits for 600ohms dynamic microphone does it produce any noise
how can i add one more mic and aux?
what will be the output voltage
can i use LM741 instead of TL072
sorry for too many questions
Hello apex reply me
is this pre amp suits for 600ohms dynamic microphone does it produce any noise
how can i add one more mic and aux?
what will be the output voltage
can i use LM741 instead of TL072
sorry for too many questions
No noise with 600ohms dynamic microfone
For more channels uso more ML3 preamps and mix outputs
Output voltage is 1,5V rms
No LM741 is single OP, TL072 is dual.
Apex,
Many thanks for sharing your project with us.
I'm wondering do you have any plan to make electronic x over with phase control and parametric eq in one board?
best rgds
Many thanks for sharing your project with us.
I'm wondering do you have any plan to make electronic x over with phase control and parametric eq in one board?
best rgds
Subwoofer X-over with inputs from line or speakers.
APEX do you have a 2 band tone control made with transistors instead of opamps?
you posted a tone control circuit a long time ago with a tl074 quad operational amplifier).its working good.i attach a photo of it. do you have the same circuit with pcb but with 2 opamps? i have 2 opa2134 (dual operational amplifiers) and i want to use them.
you posted a tone control circuit a long time ago with a tl074 quad operational amplifier).its working good.i attach a photo of it. do you have the same circuit with pcb but with 2 opamps? i have 2 opa2134 (dual operational amplifiers) and i want to use them.
Attachments
Apex,
Many thanks for sharing your project with us.
I'm wondering do you have any plan to make electronic x over with phase control and parametric eq in one board?
best rgds
I have several active x-overs for active speakers and subwoofers, and I will share diy versions.
Regards
- Home
- Live Sound
- PA Systems
- Mic, Line, EQ... Preamps