Here's a nice solution, bayonet MIL AC connector set. 500V 25A, $7 set
1-set Military Gold 4-Pin Male Radio Female Circular Connector Y2M4ZJ + Y2M4TK | eBay
I think for an authentic "retro" look tube amp though, I would still want something like the old Amphenols. And they are so practical besides. Round chassis hole, fits an extension cord. Bullet-proof.
To H_ll with IEC, they look so cheap and plastic and hard to use. Throw-away stuff comes with those. The dump is full of them.
Hmmm, could go to the dump with a big Greenlee circular punch and punch out the IEC holes in the chassis there, then mount the round punch-out over a circular hole in your Amp chassis.
1-set Military Gold 4-Pin Male Radio Female Circular Connector Y2M4ZJ + Y2M4TK | eBay
I think for an authentic "retro" look tube amp though, I would still want something like the old Amphenols. And they are so practical besides. Round chassis hole, fits an extension cord. Bullet-proof.
To H_ll with IEC, they look so cheap and plastic and hard to use. Throw-away stuff comes with those. The dump is full of them.
Hmmm, could go to the dump with a big Greenlee circular punch and punch out the IEC holes in the chassis there, then mount the round punch-out over a circular hole in your Amp chassis.
Attachments
Last edited:
Here's a nice solution, bayonet MIL AC connector set. 500V 25A, $7 set
1-set Military Gold 4-Pin Male Radio Female Circular Connector Y2M4ZJ + Y2M4TK | eBay
I think for an authentic "retro" look tube amp though, I would still want something like the old Amphenols. And they are so practical besides. Round chassis hole, fits an extension cord. Bullet-proof.
Not sure about knock-offs, but the original Amphenol multipins connectors are bulletproof.
I'm not a fan of those old Amphenol chassis mount "Edison" plugs. I'm sure they work great, I just can't stand the look of them.
Finally found what I've been looking for. Mini Twist-Lock connectors. (Hubbell) 1.19 inch diameter.
I saw something like these on an old sewing machine once (even smaller, like 0.75 inch diameter). But searching for sewing machine connectors was futile. Seems Hubbell has a new take on this now, with an extended center ground pin for safety when inserting or removing a "HOT" cord. (pics 4 and 5)
NEMA standards:
NEMA ML-3P and ML-3R were the older 3 pin version, without the safety -extended- ground pin.
NEMA ML-2P and ML-2R are a newer 3 pin version, with the -extended- safety ground pin. These would be ideal for DIY audio amps, just what the doctor ordered. A round mounting hole, you can get a steel or SS mounting shell. Like a miniature version of the old Amphenol / Edison connector.
Midget Twist-Lock | Locking Devices | Wiring Devices | Electrical & Electronic | Products | Wiring Device - Kellems
I saw something like these on an old sewing machine once (even smaller, like 0.75 inch diameter). But searching for sewing machine connectors was futile. Seems Hubbell has a new take on this now, with an extended center ground pin for safety when inserting or removing a "HOT" cord. (pics 4 and 5)
NEMA standards:
NEMA ML-3P and ML-3R were the older 3 pin version, without the safety -extended- ground pin.
NEMA ML-2P and ML-2R are a newer 3 pin version, with the -extended- safety ground pin. These would be ideal for DIY audio amps, just what the doctor ordered. A round mounting hole, you can get a steel or SS mounting shell. Like a miniature version of the old Amphenol / Edison connector.
Midget Twist-Lock | Locking Devices | Wiring Devices | Electrical & Electronic | Products | Wiring Device - Kellems
Attachments
Last edited:
AHa, here is the old sewing machine connector. 3/4 inch diameter. Two prong. Probably Bakelite, instead of the Nylon now.
Vintage Hubbell Small Twist Lock Electrical Plug Connector | eBay
Vintage Hubbell Small Twist Lock Electrical Plug Connector | eBay
Attachments
Last edited:
Since the topic has drifted a little off IEC anyway... I bought a bag of these and can attest that they handle high voltage great, look great too. Way cheaper than Amphenol. 25mm diameter so pins have a lot of breathing room and are thick. The seller shipped incredibly fast too I think it was less than a week.
10Set GX25 XLR 2 3 4 5 6 7 8 9 10 Pin 25mm Female Male Disc Flange Panel Mount Socket with Dustproof Cover Aviation Connector-in Connectors from Lights & Lighting on AliExpress
10Set GX25 XLR 2 3 4 5 6 7 8 9 10 Pin 25mm Female Male Disc Flange Panel Mount Socket with Dustproof Cover Aviation Connector-in Connectors from Lights & Lighting on AliExpress
Those are great connectors Windcrest.
My Alesis mixer uses it for the power supply (28V), but I'm not familiar with the voltage ratings of that range of connectors.
They are sturdy, I use a lot of Amphenol MIL stuff at work, and these arent much of a compromise in that regard.
Plus chrome is so much nicer than olive drab
My Alesis mixer uses it for the power supply (28V), but I'm not familiar with the voltage ratings of that range of connectors.
They are sturdy, I use a lot of Amphenol MIL stuff at work, and these arent much of a compromise in that regard.
Plus chrome is so much nicer than olive drab
Given where they're coming from I'm a little skeptical about the quality, but that type of connector is great.
It worked out well! Managed to convert a Quad II to use an IEC C5/C6 connector with no metal work, apart from some 1mm alu plate to mount the socket, and also an illuminated switch and fuse.
Attachments
- Home
- Amplifiers
- Tubes / Valves
- IEC Power Connector