YWH:
Can you supply bulb for HPVP6121 projector..
LAMP: USHIO
Type No: NSH200BQ
Max. Wattage: 200W
also I have a NSH200CT, can i use this bulb instead of the NSH200BQ?
Many thanks.
Can you supply bulb for HPVP6121 projector..
LAMP: USHIO
Type No: NSH200BQ
Max. Wattage: 200W
also I have a NSH200CT, can i use this bulb instead of the NSH200BQ?
Many thanks.
your bulb is 200W NSH, DC,you can order JYS/DC 200w is cheaper, $40 each, only.but not so bright, about 70% brightness as 200W NSH.
other choice is 200W SBM-DC. $80 each, like 200W NSH
other choice is 200W SBM-DC. $80 each, like 200W NSH
Hi
I replaced bulb, but i have a problem.
Projector goes off after 1-2 minutes and lamp light goes on.
It ignites ok and stays on for a moment.
Could you help me how to get it stay on?
3 wires goes to the mainboard, black, red, and yellow.
What to do with them?
I replaced bulb, but i have a problem.
Projector goes off after 1-2 minutes and lamp light goes on.
It ignites ok and stays on for a moment.
Could you help me how to get it stay on?
3 wires goes to the mainboard, black, red, and yellow.
What to do with them?
An externally hosted image should be here but it was not working when we last tested it.
And more questions 😀
Im not sure about polarity. Can someone see connector that is positive?
I readed that broblem could be that polarity is wrong. I installed bulb same way that previously bulb was installed.
It should be like this, but is it really?
Im not sure about polarity. Can someone see connector that is positive?
I readed that broblem could be that polarity is wrong. I installed bulb same way that previously bulb was installed.
An externally hosted image should be here but it was not working when we last tested it.
It should be like this, but is it really?
An externally hosted image should be here but it was not working when we last tested it.
Ok thanks. I try that trick. Anything else if that wont help?
Can you say what resistor is that adjustable 47k (near that big capacitor)?
Power adjust?
What you think is the reason why it turns off?
Can you say what resistor is that adjustable 47k (near that big capacitor)?
Power adjust?
What you think is the reason why it turns off?
We run bulb with ballast in this trick. when outside projector.
adjustable 47k is Power adjust you can turn it.
adjustable 47k is Power adjust you can turn it.
Can you supply a globe for Hitachi CP-S210 Lamp DT00581 130W UHB??
If so can you let me know cost etc and how to pay.
Many Thanks
Richard
If so can you let me know cost etc and how to pay.
Many Thanks
Richard
ywh,
Any news on the 4805 lamp? If not available, how about for the Eiki LC-X990?
Thanks
Victor
Any news on the 4805 lamp? If not available, how about for the Eiki LC-X990?
Thanks
Victor
Hi ywh!
I managed to get it work. When i set bulb power to max 😀 and put projector to cool place (0c), i managed to keep it on.
Didnt try that (22c) because bulb/ballast could fail.
Seem to be that component has failed. I think so, what you think? Problem in ballast component?
I had no problem when i had previous bulb, might be that new bulb stresses more (broken) components?
Any suggestion what is broken? Lets buy cold spray and track it down.
I managed to get it work. When i set bulb power to max 😀 and put projector to cool place (0c), i managed to keep it on.
Didnt try that (22c) because bulb/ballast could fail.
Seem to be that component has failed. I think so, what you think? Problem in ballast component?
I had no problem when i had previous bulb, might be that new bulb stresses more (broken) components?
Any suggestion what is broken? Lets buy cold spray and track it down.
Hi jarkkoh
what happen when you short that pole like my picture?
there is a Thermistor in you projector I think, have you clear the dust? may too hot.
what is
(22c)
Hi recharge
OK! only bulb without reflector.
price is $80, shipping is $5.
I can take moneybooker.
Hi victor-eyd
4805 need 200W BSM-DC
Eiki LC-X990 need 200W BSM-AC
price is $80, shipping is $5
what happen when you short that pole like my picture?
there is a Thermistor in you projector I think, have you clear the dust? may too hot.
what is
(22c)
Hi recharge
OK! only bulb without reflector.
price is $80, shipping is $5.
I can take moneybooker.
Hi victor-eyd
4805 need 200W BSM-DC
Eiki LC-X990 need 200W BSM-AC
price is $80, shipping is $5
Thanks ywh
Before i sign up to moneybooker, do you take paypal? I am happy to pay thre extra fee.
Regards
Richard
Before i sign up to moneybooker, do you take paypal? I am happy to pay thre extra fee.
Regards
Richard
Hi ywh!
****
what is (22c) = degrees temp outside projector.
what happen when you short that pole like my picture? = it works as trick should do, power on but same problem stays.
***
Its not temp sensor, 1:st thing i checked.
Notified that its not temperature related problem at all.
I did check projector with cold spray. Didnt find anything.
I added extra 10k resistor to power adjust and get 57k.
It stays now longer on, but see this picture. Cant make it work with that bulb. Help please 🙂
How much voltage that bulb require?
Bulb that you say you sended me was 200W BSM-AC-H.
****
what is (22c) = degrees temp outside projector.
what happen when you short that pole like my picture? = it works as trick should do, power on but same problem stays.
***
Its not temp sensor, 1:st thing i checked.
Notified that its not temperature related problem at all.
I did check projector with cold spray. Didnt find anything.
I added extra 10k resistor to power adjust and get 57k.
It stays now longer on, but see this picture. Cant make it work with that bulb. Help please 🙂
How much voltage that bulb require?
Bulb that you say you sended me was 200W BSM-AC-H.
An externally hosted image should be here but it was not working when we last tested it.
- Status
- Not open for further replies.