JOE DIRT® said:
I would use an epoxy based resin if I am getting what your asking about correct ??
Sorry for the confusion, I meant the best tap and fluid for 0-80 holes in copper. I was looking to recommend something for DIY'ing a couple of set screws for putting a capsule on the end of a pipe fitting sort of like assembling an eyepiece.
Dear David,
I am too stupid to put my name on the Wicki board.
I want to have two boards, please.
Please put my name on the list, thank you very much.
I dont want to destroy the list with my edit.
with kind regards
Sam
I am too stupid to put my name on the Wicki board.
I want to have two boards, please.
Please put my name on the list, thank you very much.
I dont want to destroy the list with my edit.
with kind regards
Sam
Hi khundude,
I'm setting up paypal and it should be ready in a couple of days.
Look for the announcement by Wednesday.
-David
I'm setting up paypal and it should be ready in a couple of days.
Look for the announcement by Wednesday.
-David
David, last I looked we were down for 122 boards. With that price break at 70 then 100 boards would 150 boards qualify
for another price break? I would be ok with just setting the price
to $11@ + postage and if we qualify for another price cut just
donate the extra $ or 2 to DIY Audio.
for another price break? I would be ok with just setting the price
to $11@ + postage and if we qualify for another price cut just
donate the extra $ or 2 to DIY Audio.
Hi Woody,
The board house will discount another $1 to $10 a board for 150 units.
I might retain the additional dollar as a donation to DIYAudio, unless others who are participating in this GB would object. It's nice to give a little back to Jason, since he runs this site on a shoestring with a lot of volunteers.
-David
The board house will discount another $1 to $10 a board for 150 units.
I might retain the additional dollar as a donation to DIYAudio, unless others who are participating in this GB would object. It's nice to give a little back to Jason, since he runs this site on a shoestring with a lot of volunteers.
-David
I am for the donation. Without diyAudio.com most of us would never get an opportunity to get PCB's like this.
How to Pay for Boards
Hello F1 GB Participants,
Please pay for your boards via PayPal using the following link: Buy F1 GB Boards
*** Deadline for payment is Jan. 12, 2009 ***
If you do not have PayPal, payment can still be made with a credit card during checkout.
The Buy button defaults to 2 boards for 2 channels. Additional boards and shipping options are available during checkout.
Please email if you have any questions. Any balance above actual costs will be donated to DIYAudio.com.
There maybe a few boards leftover after the GB closes, but order before the deadline to guarantee a set.
Thank you Nelson for your VERY generous approval and lending of your IP for our DIY non-commercial F1 GB.
-David
Hello F1 GB Participants,
Please pay for your boards via PayPal using the following link: Buy F1 GB Boards
*** Deadline for payment is Jan. 12, 2009 ***
If you do not have PayPal, payment can still be made with a credit card during checkout.
The Buy button defaults to 2 boards for 2 channels. Additional boards and shipping options are available during checkout.
Please email if you have any questions. Any balance above actual costs will be donated to DIYAudio.com.
There maybe a few boards leftover after the GB closes, but order before the deadline to guarantee a set.
Thank you Nelson for your VERY generous approval and lending of your IP for our DIY non-commercial F1 GB.
-David
Alan,
Your so right, a good amp like this needs great full range drivers. I have access to a 8'x8' CNC 3 axis router. It would be fun to kick out complex speaker boxes on this machine. It's pretty cool to drop a large sheet of MDF on the table and watch the CNC machine go to town.
-David
Your so right, a good amp like this needs great full range drivers. I have access to a 8'x8' CNC 3 axis router. It would be fun to kick out complex speaker boxes on this machine. It's pretty cool to drop a large sheet of MDF on the table and watch the CNC machine go to town.
-David
Hi David,
Just sent payment for 4 boards (2 stereo) but note that shipping cost has yet been included. Are you going to advise the shipping cost so that I can send payment for shipping.
I am from Hong Kong.
Regards
Andy
Just sent payment for 4 boards (2 stereo) but note that shipping cost has yet been included. Are you going to advise the shipping cost so that I can send payment for shipping.
I am from Hong Kong.
Regards
Andy
- Status
- Not open for further replies.
- Home
- Group Buys
- F1 Group Buy