Babowana said:Wow hell ugly !!!
I like this one:
An externally hosted image should be here but it was not working when we last tested it.
hehe.............. 3 hands 😉
Yunick said:
David - look at pic
put one blob of thermal grease between two BC critters in input CCS and tie them with something .........plastic zip thingie or whatever ;
they must be tight coupled, because these two have opposite tempco...that way you'll have rock solid CCS and less variation in output offset
Attachments
Yunick said:
Thank you too, for nice words and works...
Choky and me just want to share thousands hours and dollars spended on audio and music equipment, with other similar enthusiasts.
Wi don't like make too complicated and expensive units, but simple and more then 'good enough' (like Choky said).
Game about creation audio units is similar for me like seducing a woman...
...you never know what's will be happen
So, just go ahead friend!!!
vangelis said:
............
Game about creation audio units is similar for me like seducing a woman...
...you never know what's will be happen
............
too old for R'n'R , to young to die................
as I said before - Vangelis is my better half......but I can't resist......
(ask him what's his wife occupation.......and what can happen if he mess with woman seducing...........hehe .......some little creature in bed 😉 )
on second thought .........same creature can make a way to my bed,if I take too much of his time with my babbling........ 😉
Thanks you Babo 🙂
It sure do come in handy from time to time.. 😉
They will be there when we fire up, Thanks for the tip 🙂
The construction has been delayed a couple of days.. The Alu to join the heatsinks on my brothers Mini-a chassi where to small. We will try to get some bigger tomorrow..
Work is in progress.. but it's slow.. Wish I hade steeone's pace 🙂
My brother has been working late this week and this weekend he's going away to south of sweden cos a friend is getting married 🙂
I'm almost finished... I'm soldering the cables and mounting tha last bits..
Maybe an hour or so... 🙂
Yunick said:
just remember to cool it ........20 min with a beer ,before final check 😉
and - cigar after ..........listening da musak !
😉
Success!!!
We got music playing... 😀😀😀
I'll be right back... Got to make the final adjustments.....
We got music playing... 😀😀😀
I'll be right back... Got to make the final adjustments.....
Thank you 🙂
As it plays now the power supply puts out 23.6 Volts, DC offset 32mV, 2.3A Bias... 😀😀
An externally hosted image should be here but it was not working when we last tested it.
Rest of the chain.. dddac.de with USB, BOZ with russian PIO, DIY2000 speaker vinners.
An externally hosted image should be here but it was not working when we last tested it.
Sound impressions.... 😀😀😀
It's a biiiig leap from the Aleph30 i used before.. The top end is just unreal... But what I didn't expect was the massive bottom end.. 😀😀😀
I could not be happier... This is by far the best I have heard in my system.. I have previous have buildt Chip amp, Mini-A, Aleph30.
Thanks Zen Mod and Oly for the support and for making this possible.
Thanks Steenoe and cviller for inspiration.
Yunick said:
Now, why did I know you would say that😀
Nice to see another enthusiastic owner of the Babelfish.
What are the heatsinks, from the Conrad GB?
Steen🙂
Yunick said:
as I always bable to my man steen...........now is time for better speaks 😉
read between lines........something with bigger cones
...... and I'm not thinkin' on car subs drivers 😉ya ready for nice open baffles?
seems that's time for me to think-after Pumpkin- about nice LU based follower amp........
edit:
be prepared-after few days listening like that - to make final offset adjusting with cover on top.
procedure -power up -wait -pull cover -adjust -put cover on -wait -and again
hehe...........'nuff fun for few hours 😉
ps. I like way how you clamp mosfets
Zen Mod said:
as I always bable to my man steen...........now is time for better speaks 😉
read between lines........something with bigger cones
ya ready for nice open baffles?
seems that's time for me to think-after Pumpkin- about nice LU based follower amp........
The Yunick man may have Pass'ed out briefly, listening to that J-fet thing😀
LU follower? I am all ears😉
steenoe said:
ZM surprised..........?
Naaaah......... (talkin' jacccccovity slang)
is it bad that I'm just only one ........ full with crazy ideas ,but without 'nuff time ..........
repetitio est mater studiorum .........
seems that yunick boy is
1. celebrating , or
2. celebrating and listening ,or
3.silly looking at silly smoke commin' from amp..........
I hope it isn't No.3
or he's just where all young ppl are in the evening hours ;
not like some old farts ........
1. celebrating , or
2. celebrating and listening ,or
3.silly looking at silly smoke commin' from amp..........
I hope it isn't No.3
or he's just where all young ppl are in the evening hours ;
not like some old farts ........
I'm still here.. 😀😀
Soon after my last post, My son arrived and we went fishing, that I earlier promised him....
There will be a longer listening session tomorrow night....
From Conrad, yes... MF35-151.5 ..
Hehe... Thanks 🙂
Now of to finish the Aleph p1.7 that never got finished... :/
Soon after my last post, My son arrived and we went fishing, that I earlier promised him....
There will be a longer listening session tomorrow night....
From Conrad, yes... MF35-151.5 ..
Hehe... Thanks 🙂
Now of to finish the Aleph p1.7 that never got finished... :/
Conrad Heatsinks
Hi Yunick,
How hot do the heatsink and the MOSFET get with the Conrad heatsinks? They are exactly the ones I was going to buy for a Babelfish-J and a Babelfish - J - X.
Regards,
George.
Hi Yunick,
How hot do the heatsink and the MOSFET get with the Conrad heatsinks? They are exactly the ones I was going to buy for a Babelfish-J and a Babelfish - J - X.
Regards,
George.
- Status
- Not open for further replies.