AussieAmplifiers NX150 Spyder

Status
Not open for further replies.
Realy busy for the casing

This is the heatsink for my X1 amplifier 😀
They drill some holes in the black body
For a screw from other parts join with them

This heatsink is very cheap US$ 7 😀
For cutting the shape take cost US$ 20 per pair :devilr:
If im live in Australia I will buy Conrad Heatsink, realy :xeye:

This will take another two process to make it them perfect
The last is Anodized, before that must clean from a scratch first
Oh my money ….. oh my money … :bawling: :bawling: :bawling:
 

Attachments

  • img_0843.jpg
    img_0843.jpg
    39.7 KB · Views: 1,216
Original Heatsink Shape

This is the real heatsink when I found them in Used Market
I don’t know from where planets they coming from 😕

Looks bad with unoriginal audio heatsink (L shape) :apathic:
And came with very minimum measurement (250mm) :apathic:

What make me interest, they were very cold when I touched it 😀
Even in the hot afternoon tropic climate 33’ Celcius 😀

So I work my additional job for the heatsink :bawling:
Spending more time … must more control … very tired :hot:
 

Attachments

  • img_0860.jpg
    img_0860.jpg
    44 KB · Views: 1,207
PACKAGE

Look another package come from netherland
What is this inside the package ???
Is this from Jacco Vermeulen ??? 😀 😀 😀

Jacco you must send to me sometime :hot:
I receive capacitor, resistor or PCB even your amp 😀
 

Attachments

  • img_0856.jpg
    img_0856.jpg
    72.5 KB · Views: 1,167
Feets

Ohhh GOD ! Ohhh YES ! ….. My Preamp coming !!! :bigeyes:
Lets dance :angel:… Lets drink a while :angel:… open a bottle red wine

Im very afraid they come unsafely like DX board shipment
Have a crack in the PCB (according Carlos statement 😱)

Please look the white box inside the main box 😎
Their the amp feets :hot:, I order more 4 feets for my power amp

Will be look nice if the pre amp feet same shape with power amp ?
Of course ! This is my dream from the begining 😀 😀 😀

THIS PROJECT IS REALY SERIOUS FOR ME
ALL THE THING MUST IMPORT IS TAKE TIME TO LONG
 

Attachments

  • img_0857.jpg
    img_0857.jpg
    35 KB · Views: 1,218
Unfinish & Tested

Im glad that my work have a result for the last
My casing is finish

I tested and the casing was streng enough
Maybe better after finishing process

This is my humble casing
 

Attachments

  • casing.jpg
    casing.jpg
    36.3 KB · Views: 1,213
a little research

After rest for a while
After a big holiday
After all office activity gone away

After learning a new idea in DIY AUDIO
( I love Grandpa John Cruel a lot 😀 )
After active communication with the old friend
After see a lot of new friend

After looks some group buys
After search for trading post
After sell a lot of stuff

WOOOWWWWW A lot of thing to do :hot:
Im glad till this day im alive

Lets go to continue this NX 150
Sorry for destroyer X i didnt this casing to you 😎
 
cable and connector research

theres a lot of to do with the cable
trying one by one, want to know what i do
ha ha ha ha 😀

1. try the cable for home appliance name Eterna
2. try the cable for car
3. try the belden cable for computer
4. try the canare cable for audio
5. try the belden cable for audio
6. try the alpha cable - silver
7. try the isotek cable
8. try the Russian Fighter Cable :bigeyes:

Believe it or not
Some cable have their own sound .....
Because Si_Jopie try in his PCB so i stop posting
( I dont want something happen in my PCB 😀 )

Ha ha ha if you can research with anybody stuff
why must you reject ... I got a lot of experience
in there
 

Attachments

  • solder.jpg
    solder.jpg
    55.6 KB · Views: 1,111
Front plate ( not anodize yet )

I start to leave my perfectionist
after finished make a good front plate
i dare to take picture and attach them

My Front plate just like an usual
i use bulgin switch ( with blue ring )
... Oh how wonderful the light
To power it, i buy Smithy666 softstart

and in the center of the frontplate
i use a little led 3mm with a blue light too
im glad the led hole is perfect
they can hold the led very good
 

Attachments

  • frontplate.jpg
    frontplate.jpg
    35.5 KB · Views: 1,030
back plate ready

To complete my encapsulate
so i start to drill some hole in my plate

4 hole to speaker output
2 hole for rca input
2 hole for xlr female input

for my power cable i dont use any connector
but the cable came from the bottom
i use belden 83803 with lenght 2.5 m
i think it was enough
 

Attachments

  • backplate.jpg
    backplate.jpg
    40.8 KB · Views: 1,048
thank you for info

Before i forget
i would like to say thank you for Walter Buckhard

For his "wierd" cable info
The Russian Fighter Cable .....
i found it in Singapore :hot:

So anybody will donour me
Nasa Cable or Fighting Falcon Cable 😀
 
Hii Jleaman

If i attach picture in forum, the picture cant bigger
more than 100kb in attach file

so i go to photoshop sometime i crop them
sometime i resize them in editing process

Maybe if i use Canon Ixus the picture data is too
big, more than 2Mb

If you still needed the big resolution i can send you
via email 😀, i can send too for all NX 150 lover 😎

Ohhh yes my finggir is realy tired to make the alumunium
face like mirror, everybody can make it, try this at home

Buy Amplas for metal from hard, medium and soft you can
find in material store try to use from the hardest than to
medium and the soft one
 
jeffry_widjaja said:
Hii Jleaman

If i attach picture in forum, the picture cant bigger
more than 100kb in attach file

so i go to photoshop sometime i crop them
sometime i resize them in editing process

Maybe if i use Canon Ixus the picture data is too
big, more than 2Mb

If you still needed the big resolution i can send you
via email 😀, i can send too for all NX 150 lover 😎

Ohhh yes my finggir is realy tired to make the alumunium
face like mirror, everybody can make it, try this at home

Buy Amplas for metal from hard, medium and soft you can
find in material store try to use from the hardest than to
medium and the soft one


your attaching a 150x100pix image you can add a 800x600 one, when you go to save with photo shop use save for web it will lower the quality, and then show a better and bigger picture, if you need help let me know.

J'
 
Test .. one .. two .. three

Now this is time to start to listen the NX150S

For this testing my friend order 500va, 2 x 40v
because he want use the Elna Capacitor 12000 uf 63 v

connect all the cable and connector
lets turn on the switch 😀

and ... listen first attach picture later
 
After 48 hours

With my less experience in audio world
This NX 150 is the amp more than I expected
With the better staging, better detail and better vocal

I hear several song like, Africa from Toto
A lot of amazing sound arrived
I don’t now where they are with my old amp

Someone said that Mofset isnt include in audio family
But after I hear this amplifier, It is a beautiful sound
Maybe i get better with other but this amp is more
than enough for me
 

Attachments

  • nx150.jpg
    nx150.jpg
    33 KB · Views: 1,328
Status
Not open for further replies.