Predator864 said:
If you meant Russian 6P3S (6pi3s), which is a tetrode, then it is 6L6 equivalent.
6P3S datasheet
Predator864 said:
those are very old article ( 96?), I'm not sure to still have the magazine
, have to check.
🙄
Today I`ve sent an email to Bartolomeo Aloia (aloiabartolomeo@tin.it).
Maybe I should ask him more about the output transformers.
This design will benefit from a more elaborate PSU ?
Maybe I should ask him more about the output transformers.
This design will benefit from a more elaborate PSU ?
Good thing!
Mr.Aloia has various steps for PSU, it is one of his battle horses!
From normal CLC up to LCLC !!
chocke input. And note that the PSU is " in parallel", not" in series" ( I have read so).
You are in very good hands !😉
Cheers,
Paolo
Mr.Aloia has various steps for PSU, it is one of his battle horses!
From normal CLC up to LCLC !!
chocke input. And note that the PSU is " in parallel", not" in series" ( I have read so).You are in very good hands !😉
Cheers,
Paolo
Predator864 said:
I don't know it. For sure it is a gentleman.
Maybe he can give you some specs for build yourself the transformer, just to save money for unuseful shipping costs!.😀
Cheers,
Paolo
Found this transformers :
http://cgi.ebay.com/600OHM-SE-AUDIO...|240:1318|301:1|293:1|294:50#ebayphotohosting
On paper they look OK.
http://cgi.ebay.com/600OHM-SE-AUDIO...|240:1318|301:1|293:1|294:50#ebayphotohosting
On paper they look OK.
Predator,
I'm not sure to understand your choice because BA design is IMO a sort of parafeed;
it employ a transformer without air-gap🙄
Cheers,
Paolo
I'm not sure to understand your choice because BA design is IMO a sort of parafeed;
it employ a transformer without air-gap🙄
Cheers,
Paolo
Call me Bob.
Oh. Thanks again (and again) Paolo for the tip.
Now all I have to do, is to wait for Mr. BA to reply.
Oh. Thanks again (and again) Paolo for the tip.
Now all I have to do, is to wait for Mr. BA to reply.
Hey Bob 🙂 ,
Excuse my question: are you sure to have the instruments to build yourself that monster?😀
Because It seems to me it is not the typical basic SE;
It is IMO not an easy task
🙄
But I am really newbie on tubes, so my point is just impression, of course!🙂
Hey, what type of speakers do you have to drive with it?
Big room or little?
Cheers,
Paolo
Excuse my question: are you sure to have the instruments to build yourself that monster?😀
Because It seems to me it is not the typical basic SE;
It is IMO not an easy task
🙄
But I am really newbie on tubes, so my point is just impression, of course!🙂
Hey, what type of speakers do you have to drive with it?
Big room or little?
Cheers,
Paolo
I have many speakers 😀 from low to high efficiency.
Time is my ally, I will not rush this project.
About the instruments, I`m looking forward to purchase some measurements tools.
I like challenging projects. More important is the info you gather about them. The rest is simple.
Time is my ally, I will not rush this project.
About the instruments, I`m looking forward to purchase some measurements tools.
I like challenging projects. More important is the info you gather about them. The rest is simple.
I've used those. They do well, but only up to about 10W of output power.
Edcor has a 600ohm CXSE transformer (http://www.edcorusa.com). I am using a pair now in a 6c33c SE. They are considerably beefier and will only cost you $20 more per transformer. Even though they are rated at half the power of the eastern audio transformers, in real life they will handle about twice. I guess Edcor is rated in US watts and the EA is Chinese watts. 😀
Edcor doesn't list the 600ohm transformers online. You have to call or possibly e-mail to order them.
Their current 600ohm design has %50 taps. I had them add those for a local feedback experiment. You can have them remove the taps, since you won't be using them.
I have been mulling over Dmitry Nizh's inductor coupled design for a while now, and even have the ECC99's and 6C33C's at the ready! So I will have to give those OPT a look myself. I was thinking of using the UBT-1's or something similiar. Most of the SE circuits floating about for this tube insist on some exotic iron, which is what appeals to me with this design, as well as the linear driver tube, and the operating range of the output tube. Has anyone else used this design?
If you want a good SE,go with these design:
http://www.metaleater.narod.ru/6c33c.gif
If you want a very good SE you should try Romy design:
http://www.metaleater.narod.ru/6c33c.gif
If you want a very good SE you should try Romy design:
Attachments
- Status
- Not open for further replies.