Photo Gallery

[hellotron]

Hi. My last amplifier DIY - used tubes 2 x ECL80, power output 2 x 1.5W / Speakers 4-8 Ohm or Headphones 32-600 Ohm.

 

[inguz]

Very neat!

 

[hpeter]

 

[subbu68]

Hi. My last amplifier DIY - used tubes 2 x ECL80, power output 2 x 1.5W / Speakers 4-8 Ohm or Headphones 32-600 Ohm.

Nice vintage looking amp.

That blue light is distracting though. Amber LED would look nice with the glow of the tubes. For my amp (Elekit) I had suggested this to Elekit.

 

[hellotron]

Thank all for praise. The "eye" is not lit blue so intense, I've reduced him voltage matched resistor, only camera so exaggerate.
Yes, later will also be colored amber.

 

[jean michel]

Hi. My last amplifier DIY - used tubes 2 x ECL80, power output 2 x 1.5W / Speakers 4-8 Ohm or Headphones 32-600 Ohm.

hello ... so very good job

 

[JohnTubeamp]

Hi,

Hi. My last amplifier DIY - used tubes 2 x ECL80, power output 2 x 1.5W / Speakers 4-8 Ohm or Headphones 32-600 Ohm.

It's a beauty !!!

 

[hellotron]

Thanks. Scheme on the basis of which I built amplifier...

 

[Bigun]

Mono pentode amp ('Yukon Gold')

 

[MagicBus]

Now, that's what I call modeling electronics! Like old japanese transistor radios. I like it very much!

 

[dady]

The big transformer is the audio one?
It is a precious piece of electronic.

 

[hpeter]

Now, that's what I call modeling electronics! Like old japanese transistor radios. I like it very much!

i was surprised, how much effort japanese put into 1626 and such

 

[MagicBus]

I know this doesn't belong here but I can't fight it... ATJ's post #7513 and Bigun's latest have set me on fire!
http://www.ifixit.com/Teardown/Sony+TR-63+Transistor+Radio+Teardown/1219

 

[JohnTubeamp]

I know this doesn't belong here but I can't fight it... ATJ's post #7513 and Bigun's latest have set me on fire!
http://www.ifixit.com/Teardown/Sony+TR-63+Transistor+Radio+Teardown/1219

I still have some of these transistor radios in my collection. Lately I repaired an EKCO one !!!

 

[Wavebourn]

Learning 3-D printer... ;-)

 

[TonyTecson]

6C33 OTL amp.....

 

[scottpetersen]

Learning 3-D printer... ;-)

A friend of mine helped me make these missing pieces for my C20 that was out on junk day.
The upper one is the one I put together,I bought the lower one to copy
I still have to make the end caps,They are the unavailable narrower size

 

[Wavebourn]

A friend of mine helped me make these missing pieces for my C20 that was out on junk day.
The upper one is the one I put together,I bought the lower one to copy
I still have to make the end caps,They are the unavailable narrower size

ABS filament?

 

[scottpetersen]

Not ABS, it is PLA. The plexiglass neon orange wing is adhered in with acrylic solvent,Pla can be "glued" with acrylic solvent in small quantities,to build up
assemblies

 

[Wavebourn]

Not ABS, it is PLA. The plexiglass neon orange wing is adhered in with acrylic solvent,Pla can be "glued" with acrylic solvent in small quantities,to build up
assemblies

A bezel printed with PLA: