I think is going to end up this way - biamp.
Will try 150-100Hz with 1st order.
Need to change fostex for something better.
Note:
The Mod.s need to create a new thread for sawik1977 and transfer most of the posts over the last 2 pages. Perhaps from post 1151 on.
The Mod.s need to create a new thread for sawik1977 and transfer most of the posts over the last 2 pages. Perhaps from post 1151 on.
Sonido 400 datasheet http://www.sonido.hu/adat_pdf/scw-400.pdf
"Those who wish to buy our products should contact us directly"
info@sonido.hu
"Those who wish to buy our products should contact us directly"
info@sonido.hu
My OB/H-frame project called Open Invit8tions. LCY110, Audax HM130Z0, dual Peerless 830667's The crossover between the mid/tweeter is based off the AR-SXO capacitorless serial topology and the woofers use a standard 12dB LP.
Build pics:
Open Invit8tions Photos by 6thplanet | Photobucket
TanTon
Hello,
although they are not brand new and the photos are crap I think they are worth to be in this gallery.
The TanTon I developed around 2011 and they please me with wonderful sound since then. The baffles are made of felt bond with a little backbone magnet to magnet.
[/IMG]
[/IMG]
Drivers are Tang Band W6-1530SA, Visaton GF 250 and a bit modified Raveland ( Mivoc ) AXX 1515.
0° - 90° 10 degree steps:
[/IMG]
Thread in german : TanTon Coax Dipol - DIY-HIFI-Forum
All the best
Fabian
Hello,
although they are not brand new and the photos are crap I think they are worth to be in this gallery.
The TanTon I developed around 2011 and they please me with wonderful sound since then. The baffles are made of felt bond with a little backbone magnet to magnet.
Drivers are Tang Band W6-1530SA, Visaton GF 250 and a bit modified Raveland ( Mivoc ) AXX 1515.
0° - 90° 10 degree steps:
Thread in german : TanTon Coax Dipol - DIY-HIFI-Forum
All the best
Fabian
Very nice looking design, should be good dynamics and big mage scale..
What makes me doubt: - possibility of integration of this tweeter with FRm both with horns
- and horn and 200SFR probaly works not so low like you cross it over mating with 400scw...
Wow! We used this design idea with my partner, but did not see Roberts design before.
details at www.flagmanspeakers.com
Attachments
My OB/H-frame project called Open Invit8tions. LCY110, Audax HM130Z0, dual Peerless 830667's The crossover between the mid/tweeter is based off the AR-SXO capacitorless serial topology and the woofers use a standard 12dB LP.
Build pics:
Open Invit8tions Photos by 6thplanet | Photobucket
You're right. I have to change tweeter. Possibly fountek or Audax.
I really like the LCY110, it's a nice tweeter with exhalent vertical dispertion for a ribbon. Probably due to the "squareness" of the ribbon. Can't go wrong with the Areogel mids either...
Attachments
DIY dipoles. CNC cutted MDF. 2K proffessional paint. Acryllic wings. 75 cm wide.
Radian 475 Beryllium in Autotech Tractrix 1000 horn
JBL 2119 8 inch
Acoustic Elegance LO15 with custom foam surround
Passive crossover for mid and high
Active low pass for the woofers via First Watt B4
Low pass 24 dB active 160 Hz Linkwitz Riley
High pass 6 dB passive 300 Hz LR
Low pass 12 dB passive 3000 Hz LR
High pass 18 dB passive 3000 Hz LR
All slopes summed 24 dB LR acoustical
No EQ, baffelstep, notch etc.
30 Hz --> 20.000 Hz +++
Woofer effective sensitivity ca 99 dB (singel ended via First Watt B4)
Mid/high ca 95 dB (balanced)
With this configuration the woofers only need slightly reduction via B4s potmeters
Biamp with 2 x Pass Labs XA30.5.
Pass Labs XP10 preamp
DIY Buffalo II dac with huge oversized PSU
Sonos
Since the beatiful Radian Beryllium compression driver is significant damped with a L-Pad i will buy Duelund Cast resistors. Maybe it will give the little extra. Anyway, it sounds good.
Radian 475 Beryllium in Autotech Tractrix 1000 horn
JBL 2119 8 inch
Acoustic Elegance LO15 with custom foam surround
Passive crossover for mid and high
Active low pass for the woofers via First Watt B4
Low pass 24 dB active 160 Hz Linkwitz Riley
High pass 6 dB passive 300 Hz LR
Low pass 12 dB passive 3000 Hz LR
High pass 18 dB passive 3000 Hz LR
All slopes summed 24 dB LR acoustical
No EQ, baffelstep, notch etc.
30 Hz --> 20.000 Hz +++
Woofer effective sensitivity ca 99 dB (singel ended via First Watt B4)
Mid/high ca 95 dB (balanced)
With this configuration the woofers only need slightly reduction via B4s potmeters
Biamp with 2 x Pass Labs XA30.5.
Pass Labs XP10 preamp
DIY Buffalo II dac with huge oversized PSU
Sonos
Since the beatiful Radian Beryllium compression driver is significant damped with a L-Pad i will buy Duelund Cast resistors. Maybe it will give the little extra. Anyway, it sounds good.
Yes. The AE woofers deliver plenty of bass due to QTS Around 0,9 and extremely low inductance. They have Xmax of 12 mm and are made for dipoles. 🙂
No, according to AE, Q=0.82 and Xmas 9mm. But never mind, I bet bass is good😱)
I have two 830669/side and need eq. However size and q is lower than AE....
I have two 830669/side and need eq. However size and q is lower than AE....
Been lusting over those... should have bought those with the money i saved not buying an Eq... gotta love high QTS woofers eh?
0,82 yes, you are right. But x max is 12 mm since theese are custom models.