Here you can buy smaller quantities but more expensive.
schulelektronik.de - elektronische Bauelemente - Transistoren - IC´s - STK - Kondensatoren - Widerstände
Danke für dass link!
I have not been spending sufficient time following the details this Thread has exposed recently, so out of ignorance on my part, I ask a question.
Do the use of bc550c/560c as the input pairs raise the likely hood or possibility of stability issues?
Could one of each pair be specified to be lower gain and/or lower fT to help with stability?
Do the use of bc550c/560c as the input pairs raise the likely hood or possibility of stability issues?
Could one of each pair be specified to be lower gain and/or lower fT to help with stability?
Do the use of bc550c/560c as the input pairs raise the likely hood or possibility of stability issues?
Could one of each pair be specified to be lower gain and/or lower fT to help with stability?
No problem AndrewT 😉
Single transistor pair BC550C/BC560C is rock stable, no instability whatsoever. 😎
Since the wish to improve input pair to have constant power dissipation (cascoded Sziklai) was expressed, it was not tested in practice with TSSA yet. So all useful information of stability and improvement, if any, will be gathered by Gerhard and Sonnya, since they already experienced super simple TSSA from post #1. 🙂
Sziklai shouldn't have any instability problems (different with Baxandall) since Vce of input pair have enough headroom to operate in linear conditions, also Ic is almost costant ie. 0,65 mA. 😉
Replacement for Exicon and Renesas (except 2sk216 and 2sj79)
Magnatec. ALFET Lateral MOSFETs
TT electronics Semelab Limited - Magnatec Datasheets
They are stocked at Farnell.
Magnatec. ALFET Lateral MOSFETs
TT electronics Semelab Limited - Magnatec Datasheets
They are stocked at Farnell.
It appears from the various posts around the Forum, that the loss of one factory to a natural event, took down worldwide production of Lateral Power mosFETs.
This may confirm that all current product is based on the same process and the same manufacturer.
Could this be why Laterals are more expensive than Verticals? No competition.
This may confirm that all current product is based on the same process and the same manufacturer.
Could this be why Laterals are more expensive than Verticals? No competition.
I use BC327-40 and BC337-40.
The modules are nearly ready for testing.
I will let them sit for an hour and then double check.
I hope to get the amp working today.
Very nice looking modules.

Please do not forget to add 2200 uF/10 V elco from latest update. 😉
We had spring cleaning today and i am building a pair of speakers parallel. i am quite exhausted. I tested the current sources. They work but one channel started to smoke when i cranked the voltage. More testing tomorrow, sorry guys.
What do you think LC ?
I can hand you the modules on the High End and then you can play around with them.
I am simply running out of time.
I can hand you the modules on the High End and then you can play around with them.
I am simply running out of time.
What do you think LC ?
I can hand you the modules on the High End and then you can play around with them.
I am simply running out of time.
When you are on the excibition i Will have done the layout.
OK, when i find the time i will make the moduls working. Problem is that i have a lot of guests after the High End so the next two weeks it may be hard to find time for DIY. Anyway, this is exiting.
Hi guys 
A day off from the forum, so where did we stay. 🙄
Yes Gerhard, that modules looks great, very compact, just to mine taste hehe
Smoke you said, tiny little black thingy was black before anyway, smoken, no help for him anymore.

So there's obviously some mistake inside that module, plus smoken part to find. We'll use sniffy doggy style to find him, he certainly didn't have a shower in between. That's sorted 😀
Second module stays a side, first one to repair. It's good that it will operate the same with or without outputs. CCS can be isolated and tested separately, for the inputs you have to measure each BJT diodes to check functionality plus correct position in the circuit.
But you already know all that, it's just that your time schedule is too tight to fit in, I know. Well if you don't find a solution before just bring them to High End and we'll discuss from there on. 😎

A day off from the forum, so where did we stay. 🙄
Yes Gerhard, that modules looks great, very compact, just to mine taste hehe

Smoke you said, tiny little black thingy was black before anyway, smoken, no help for him anymore.


So there's obviously some mistake inside that module, plus smoken part to find. We'll use sniffy doggy style to find him, he certainly didn't have a shower in between. That's sorted 😀
Second module stays a side, first one to repair. It's good that it will operate the same with or without outputs. CCS can be isolated and tested separately, for the inputs you have to measure each BJT diodes to check functionality plus correct position in the circuit.

But you already know all that, it's just that your time schedule is too tight to fit in, I know. Well if you don't find a solution before just bring them to High End and we'll discuss from there on. 😎
When you are on the excibition i Will have done the layout.
Make it small & nasty, little poison.

Today i found a little time so one more round of testing. It must be some really small bug because i am usually good with p-p and perfboard.
ALF16P16W and ALF16N16W as output with 2SK216 and 2SJ79 as driver.
The ALF has the double gfs than ECX10n20 and ECX10p20 (1.4 - 4S against 0.7 - 2S)
What about a sense resistor in series with the source for setting the idle current. I think of the size of 0.05R!???
The ALF has the double gfs than ECX10n20 and ECX10p20 (1.4 - 4S against 0.7 - 2S)
What about a sense resistor in series with the source for setting the idle current. I think of the size of 0.05R!???
- Home
- Amplifiers
- Solid State
- TSSA - The Simplest Symmetrical Amplifier