TAS1020B-based Asynchronous USB to I2S/SPDIF converter 24bit/96kHz

Status
Not open for further replies.
Jump to Latest
#61
New Production want to buy List :

guglielmope x1 - I2S - Italy (with galvanic isolation and external oscillators)
korben69 x1 - I2S - France
Ryssen - x1 - Spdif - Sweden (external oscillators)

And I wonder,on the DC jack is the possitive in the middle?
 
#62
center pin is almost always positive

guglielmope x1 - I2S - Italy (with galvanic isolation and external oscillators)
korben69 x1 - I2S - France
Ryssen - x1 - Spdif - Sweden (external oscillators)
qusp x 1 I2S - Australia (with external oscillators)
 
#64
kp93300 said:
Hi JarekC,
Can i confirm that the usb to i2s converter works with Linux ?
The ADUM usb isolator also works with Linux ?
what the cost for both units and postage to malaysia?
thanks
kp93300
Click to expand...

Hi,

AD1. Converter works with LINUX.
It uses native driver for UAB Audio Class 1.0

AD2.
I have not tested this, but should be OK.
ADUM is transparent for USB signals.

AD3.
Shipping to any country is about 6$

Best regards
JarekC
 
#65
I am asking for more info on these 2 items
I quote
Options cost:
-external oscillators + (additional parts) 25$
-galvanic isolation module 18$
Unquote

Do you mean external oscillators with extrapower supply and the clock signal piped to the board via a wire? I have the Kwak clock and can i use this .? What clock frequencies works with the usb to i2s board ? I have a few oscillators left over from a previous project.

Is the galvanic isolation module equivalent to the digital pulse transformer for spdif output ?

thanks

kp93300
 
#66
kp93300 said:
I am asking for more info on these 2 items
I quote
Options cost:
-external oscillators + (additional parts) 25$
-galvanic isolation module 18$
Unquote

Do you mean external oscillators with extrapower supply and the clock signal piped to the board via a wire? I have the Kwak clock and can i use this .? What clock frequencies works with the usb to i2s board ? I have a few oscillators left over from a previous project.

Is the galvanic isolation module equivalent to the digital pulse transformer for spdif output ?

thanks

kp93300
Click to expand...

guglielmope x1 - I2S - Italy (with galvanic isolation and external oscillators)
korben69 x1 - I2S - France
Ryssen - x1 - Spdif - Sweden (external oscillators)
qusp x 1 I2S - Australia (with external oscillators)

Ad1.
No.
Oscillators (22.5792MHz & 24.5760MHz) + Multiplexer LCX157 + LDO +RC parts are mounted on PCB.
If you would like use Kwak clock you need 2 frequencies 22,5792MHZ and 24,5760MHz. Signals levels are 3.3V.

Ad2.
No.
Digital pulse transformer make isolation on SPDIF side.
Module (ADUM3160) make isolation on USB side.

JarekC
 
#68
Hi,

guglielmope x1 - I2S - Italy (with galvanic isolation and external oscillators)
korben69 x1 - I2S - France
Ryssen - x1 - Spdif - Sweden (external oscillators)
qusp x 1 I2S - Australia (with external oscillators)
SPWONG x1 - I2S - Hong Kong (with galvanic isolation and external oscillators)

Thanks for your works!
 
#75
gior said:
Hello,
I'm also interested in this, SPDIF version, but have no great experience with diy. Is there a list somewhere of the steps needed to have it up and running?
Thanks,
Gio
Click to expand...

Converter is ready to use.
For all systems Windows , Mac Os, Linux it uses native drivers.
So you connect converter to PC and it should be recognized automatically.
In system it will appear as "Audio device"/"USB->SPDIF V1.0x"

Sorry but at this moment SPDIF version is sold out.
New PCB version soon.

JarekC
 
#76
Hi all,

New PCB for USB-I2S version is READY.🙂
Yesterday I sent files to PCB factory, so test pices should be on my desk for 10 days.

Connectors on PCB:
USB - USB bus (type B)
I2S - I2S bus (IDC 2x5pins raster 2.54mm)
POWER - input for external power supply (2x1 pin raster 2.54mm)
JP3 - jumper for selecting USB Bus/External supply, instead jumper you can connect switch(3x1 pin rasetr 1.27mm)
LED - Power LED and Fs LEDs (each Fs has own LED) (6x1pin raster 1.27mm)
J3 -input for external master clock (4x1 pin raster 2.54mm)

Changes compared to the previous version:
-galvanic isolation on PCB (ADUM3160 + LDO)
-shorter track for Master Clock signal (from Xo to TAS1020B)
-elimination of the multiplexer in the Master Clock signal path
-sampling rate signaling with 4 LEDs (each has its own LED)
-series termination resistors on the I2S bus lines
-22.5792/24.5760MHz generators + LDO can be mounted on the PCB, or connected via J3 connector
-additional 16-bit modes for connecting 16-bit DACs such as TDA1541A, TDA1543, etc. (during testing)
-AC-3 passing through mode (during testing)
-derived power to the I2S connector, ability to supply DAC
-smaller dimensions, only 67mm x 30mm
-4 mounting holes

Best regards
JarekC
 

Attachments

  • 6114DIY-small.jpg
    6114DIY-small.jpg
    366.7 KB · Views: 750
Status
Not open for further replies.
Top Bottom