Hi Soren,
I am sorry if it has been confusing you and I understand you are in a very busy atmosphere.
I have sent the first email as per your written T&C in the receipt where: “...Soekris Europe recommends that you contact our support via mail (support@soekris.eu) before sending the product to Soekris Europe....”.
Nil return and I have no choice to send the second email to info@soekris.eu few days after...
Likely you may wish to revise the T&C if this is the case, thanks again.
I am sorry if it has been confusing you and I understand you are in a very busy atmosphere.
I have sent the first email as per your written T&C in the receipt where: “...Soekris Europe recommends that you contact our support via mail (support@soekris.eu) before sending the product to Soekris Europe....”.
Nil return and I have no choice to send the second email to info@soekris.eu few days after...
Likely you may wish to revise the T&C if this is the case, thanks again.
Hi Soren,
I've been waiting for it for years...
Daniel
Would it be possible to implement the Mastermode (MCLK OUT and FSEL IN Pins)?I will continue the work with firmware for the other boards since I'm in firmware mode....
I've been waiting for it for years...
Daniel
My DAC 1021 is not working please help me out 🙁
It used to work earlier, connected after a month.
Observed that voltage dropped to 1.5v on one channel and on other channel it is 12v
Using placid BP twisted pair audio as power supply
Regards
Raj
It used to work earlier, connected after a month.
Observed that voltage dropped to 1.5v on one channel and on other channel it is 12v
Using placid BP twisted pair audio as power supply
Regards
Raj
I interchanged the rails and still the positive rail voltage is getting dropped to 1.5v. On disconnecting the psu to DAC am able to observe 12v on both rails. Issue is observed on connecting it to dac
My DAC is gone?
My DAC is gone?
Last edited:
Positive rail draw more current according to spec. Maybe you don't have enough on the + rail?
The BP seem to have a somewhat complicated setup - maybe redo all the settings?
http://www.twistedpearaudio.com/docs/power/placid_bp_manual_2_1_2.pdf
1021:
Power Consumption
Positive Rail: 0.18A @ 10V
• NegativeRail:0.06A@10V
• Total:2.4W
• The positive supply draw about 3 times as much current as the negative; the current is
almost independent of input voltage.
//
The BP seem to have a somewhat complicated setup - maybe redo all the settings?
http://www.twistedpearaudio.com/docs/power/placid_bp_manual_2_1_2.pdf
1021:
Power Consumption
Positive Rail: 0.18A @ 10V
• NegativeRail:0.06A@10V
• Total:2.4W
• The positive supply draw about 3 times as much current as the negative; the current is
almost independent of input voltage.
//
Last edited:
Hi Soren/ some one else,
Could you please let me help me out in solving the issue.
Regards
You don't really say much, looks like you need to do some basic trouble shooting, like following the voltages from source to where the problem is, and checking currents....
@soekris, I have had issues since 2015 with latch up of K136 opamp (TS507?) on startup with my REV1 DAM1021 board. I ended up working around this issue at the time by removing the 6k resistor that connects to the UC mute pin and adding a 20K resistor to pull the pin of the 3FW48 mute control transistor to V+. As I have a downstream mute relay this seemed to work well however I have had persistent issues with random loss of lock (on any input). I discovered last night the the now unconnected UC mute pin is acting like an antenna - touching it with a probe connected to my finger inhibits lock.
So I am interested in looking to fix this properly now and reinstall uC control of mute. If I was to replace the K136 opamp in an attempt to cure the latch up issue what would you suggest? I notice from board photos that OPA317 and I think OPA365 have been installed in its place in later revisions.
So I am interested in looking to fix this properly now and reinstall uC control of mute. If I was to replace the K136 opamp in an attempt to cure the latch up issue what would you suggest? I notice from board photos that OPA317 and I think OPA365 have been installed in its place in later revisions.
@soekris, I have had issues since 2015 with latch up of K136 opamp (TS507?) on startup with my REV1 DAM1021 board. I ended up working around this issue at the time by removing the 6k resistor that connects to the UC mute pin and adding a 20K resistor to pull the pin of the 3FW48 mute control transistor to V+. As I have a downstream mute relay this seemed to work well however I have had persistent issues with random loss of lock (on any input). I discovered last night the the now unconnected UC mute pin is acting like an antenna - touching it with a probe connected to my finger inhibits lock.
So I am interested in looking to fix this properly now and reinstall uC control of mute. If I was to replace the K136 opamp in an attempt to cure the latch up issue what would you suggest? I notice from board photos that OPA317 and I think OPA365 have been installed in its place in later revisions.
I assume it's U2 you're talking about, down in the corner around J8, shouldn't really latchup, but certain powerup sequence on positive and negative rail could do it.... If you want to replace it, use either a opa317, tlv333 or ncs333. Do not use an opa365 there.
I assume it's U2 you're talking about, down in the corner around J8, shouldn't really latchup, but certain powerup sequence on positive and negative rail could do it.... If you want to replace it, use either a opa317, tlv333 or ncs333. Do not use an opa365 there.
Thanks Søren!
Hello can any body Tell me how to Connect aes ebu xlr spdif in to soekris 1021? Very thanks!
https://www.amazon.com/Switchcraft-AES-EBU-Adapter-110-75-Switchcraft/dp/B00C0NTW7W
Hi soekris according to miska the HQplayer developer:
Just curious but how did you solve this problem with your DAC?
Due to challenges with settling time you really cannot run high-bit R-2R DAC at rates like 3.2 MHz in a sensible way, it would lose lot of the precision because for each sample value it wouldn’t be able to accurately reach the correct level fast enough. More there are bits, more precisely the output voltage also needs to settle because the voltage steps are smaller.
Just curious but how did you solve this problem with your DAC?
Hi soekris according to miska the HQplayer developer:
Just curious but how did you solve this problem with your DAC?
Made it fast and used smaller resistor values. Did some test and measurements early on and posted about it looong time ago. Go back in posts or use search function.
I assume it's U2 you're talking about, down in the corner around J8, shouldn't really latchup, but certain powerup sequence on positive and negative rail could do it.... If you want to replace it, use either a opa317, tlv333 or ncs333. Do not use an opa365 there.
Thanks Søren changing U2 to a opa317 fixed my problem. Very happy 🙂
Hi,
Anyone is using REV 4? and know where to connect LifePO4 to its Vref (which regulator/OPAM should be removed, connect battery to where ...). I could find intructions from Randytsuch for REV1 or 2 only.
Thanks.
Anyone is using REV 4? and know where to connect LifePO4 to its Vref (which regulator/OPAM should be removed, connect battery to where ...). I could find intructions from Randytsuch for REV1 or 2 only.
Thanks.
Hi Guys,
No Vref mod was applied yet. Suddenly I got very low output from Soekris. I don't have volume control on Soekris. Previous stage is SDTrans384 with I2S connection. I am using Raw output. Any possibility for this issue?
Thank you.
No Vref mod was applied yet. Suddenly I got very low output from Soekris. I don't have volume control on Soekris. Previous stage is SDTrans384 with I2S connection. I am using Raw output. Any possibility for this issue?
Thank you.
Thanks for response, TNT. I always use Raw output, with volume knob at 10 o'clock position for normal listening. But yesterday I set it at Max position, output level is same as 9 o'clock of normal condition.
Already check my amplifier with other source, and it is ok.
Already check my amplifier with other source, and it is ok.
- Home
- Vendor's Bazaar
- Reference DAC Module - Discrete R-2R Sign Magnitude 24 bit 384 KHz