GM-120
How can you test with a 1khoms resistor ??
First check the voltage between the blue wire and the ground with a multimeter, and give me the result.
Important: what do you want to plug to the GM-120 ?
Marc
😕
How can you test with a 1khoms resistor ??
First check the voltage between the blue wire and the ground with a multimeter, and give me the result.
Important: what do you want to plug to the GM-120 ?
Marc
😕
Hi Marc,
Sticking a 1K resistor between blue and ground should turn the amplifier on. The 1K draws enough current to trigger the amp on. The most common fault with this circuit are blown traces and shorted e-b on the current sense transistor.
-Chris
Sticking a 1K resistor between blue and ground should turn the amplifier on. The 1K draws enough current to trigger the amp on. The most common fault with this circuit are blown traces and shorted e-b on the current sense transistor.
-Chris
Hi everybody !
Does , any of you realy have schematic of GM 120, because I wrote 6 ( six ) times to HI SPEED & Hi doesn't send me . Iam asking everybody who have schematic to send me !
linkxp@eunet.yu
Does , any of you realy have schematic of GM 120, because I wrote 6 ( six ) times to HI SPEED & Hi doesn't send me . Iam asking everybody who have schematic to send me !
linkxp@eunet.yu
Hi zeonrider,
I used to have it, sorry. It's at my old shop and unreachable.
I fixed my first ones by tracing out the circuit with a meter. It wasn't fun. I will always remember the experience.
-Chris
I used to have it, sorry. It's at my old shop and unreachable.
I fixed my first ones by tracing out the circuit with a meter. It wasn't fun. I will always remember the experience.
-Chris
check this thread:
http://www.diyaudio.com/forums/showthread.php?s=&threadid=22857&perpage=10&pagenumber=2
I think it is attached there by hispeed
in zip file.
dce
http://www.diyaudio.com/forums/showthread.php?s=&threadid=22857&perpage=10&pagenumber=2
I think it is attached there by hispeed
in zip file.
dce
HI AGAIN
Somebody asked me what wrong with amp. It wery simple.
I can't switch ON. Nothing is burned, everything is OK.For me is wery hard to repair without schematic because I dont see very small objects & I have 47 , I have money but Ican't pay & schematic cost around 20 Euro , this amp is much cheaper .
Thanks to ALL DIY-s
Somebody asked me what wrong with amp. It wery simple.
I can't switch ON. Nothing is burned, everything is OK.For me is wery hard to repair without schematic because I dont see very small objects & I have 47 , I have money but Ican't pay & schematic cost around 20 Euro , this amp is much cheaper .
Thanks to ALL DIY-s
GM-120
Hello zeonrider
If there is nothing plugged on, it's right.
The amp is not necessarily out of order.
Marc
Hello zeonrider
If there is nothing plugged on, it's right.
The amp is not necessarily out of order.
Marc
Hey all,
Stumbled onto this site through google looking for information on the gm-120 amp. Was delighted to find a schematic for this amp, but very disapointd when the ZIP file was corrupt. Anybody have a copy of it around still??
Ross
Stumbled onto this site through google looking for information on the gm-120 amp. Was delighted to find a schematic for this amp, but very disapointd when the ZIP file was corrupt. Anybody have a copy of it around still??
Ross
GM 120 Schematics
G'day,
Just thought if anyone want's the schematics I have, just email me with your address or post your address and I'll forward them to you. I also have the manual as well as the schematics.
Cheers,
Max
G'day,
Just thought if anyone want's the schematics I have, just email me with your address or post your address and I'll forward them to you. I also have the manual as well as the schematics.
Cheers,
Max
Hello...
I am an owner of an GM120 ...
Can Anyone send me some information about it
want to cable it up in my car 🙂 but have no clue how to do it.. lol
My current car audio is :
Head unit : Panasonic CQ-C7301N (2006model)
amp1 : JL audio monobloc 200W
amp2 : Xzound "1200W" 5ch (LOL LOL LOL LOL) <--- sucks , i use it on my mid-ranges
Subwoofer : 2 x 10" JL audio
6x9" : Altec Lancing
etc : BLG 6,5" + tweeters , Rockford fosgate cabels etc
I am an owner of an GM120 ...
Can Anyone send me some information about it
want to cable it up in my car 🙂 but have no clue how to do it.. lol
My current car audio is :
Head unit : Panasonic CQ-C7301N (2006model)
amp1 : JL audio monobloc 200W
amp2 : Xzound "1200W" 5ch (LOL LOL LOL LOL) <--- sucks , i use it on my mid-ranges
Subwoofer : 2 x 10" JL audio
6x9" : Altec Lancing
etc : BLG 6,5" + tweeters , Rockford fosgate cabels etc
yes but i gonne use it on my Altec lancing 6x9 , who has a high working-range to how mutch power they get... 🙂
sorry for my bad english
Tommy - Norway...
sorry for my bad english
Tommy - Norway...
GM-120
Can you give me your direct email, i have informations (Picture and schématic) for you.
Amicalement
Marc
🙂
Can you give me your direct email, i have informations (Picture and schématic) for you.
Amicalement
Marc
🙂
GM-120
Hello Dj-timoty
Do you have succeeded to connect your amplifier to you head unit ?
Please let us know.
Marc
Hello Dj-timoty
Do you have succeeded to connect your amplifier to you head unit ?
Please let us know.
Marc
http://www.bcot1.com/gm120/
It's in Flash format. When you open the file, maximize the window. Use the right-click menu to zoom in. The resolution is good once you zoom in.
It's in Flash format. When you open the file, maximize the window. Use the right-click menu to zoom in. The resolution is good once you zoom in.