PeeCeeBee V4H GB

[Vunce]

Nice!
That’s a solid brick of PCB’s

 

[kheon]

Hi Shaan,
Nice!
I want to add 2 pcbs please

Fabio

 

[shaan]

Hi members.

I will start sending invoices for shipping charge from tonight. Shipping will commence on Monday.

My roll of packing foam has been exhausted so right now going to market to get another.

Thanks for your patience.

 

[gtose]

Shaan,

I’ll take a pair from that stack if some remain!

Greg

 

[asuslover]

I have an 2x34v 400va transformer(antek as-4434 ), I hope it will be good ... what do you think Shaan?

 

[outtek]

Hi Shaan, I have made the payment for the shipping, could you be kind enough if you have the vertical 0.1 resistors on hand to add those to? I will pay them of course.

 

[shaan]

Shaan,

I’ll take a pair from that stack if some remain!

Greg

Hi Greg.

Sure. Some still remains in that stack.
Will send you invoice shortly.

I have an 2x34v 400va transformer(antek as-4434 ), I hope it will be good ... what do you think Shaan?

It will be fine. But maximum power output will be less.

Hi Shaan, I have made the payment for the shipping, could you be kind enough if you have the vertical 0.1 resistors on hand to add those to? I will pay them of course.

I am sorry but I can't send the resistors. I can only send PCBs, MOSFETs and BAV21 diodes.

 

[shaan]

GB members please note:

I have started preparing the address printouts. If your delivery address is different from what is shown in PsyPal then please share correct address via PM or email.

Thank you all.

 

[gtose]

Shaan,

Can Exicon ECX10N20/ECX10P20s be used in place of the 2SK1058/2SJ162 at 56v rails? I have some pairs I was going to use for a V4 build that I am hoping I could use for the V4H. If not, do you have any 2SK1058/2SJ162 pairs still available?

Thanks!
Greg

 

[kheon]

Shaan,

Can Exicon ECX10N20/ECX10P20s be used in place of the 2SK1058/2SJ162 at 56v rails? I have some pairs I was going to use for a V4 build that I am hoping I could use for the V4H. If not, do you have any 2SK1058/2SJ162 pairs still available?

Thanks!
Greg

Yes Exicon works for V4H as well, I've just asked Shaan

 

[outtek]

Hi, could we use 0.22ohm resistors instead of the 0.1? It shouldn't have much impact on the functionality from what i can tell.

 

[shaan]

Shaan,

Can Exicon ECX10N20/ECX10P20s be used in place of the 2SK1058/2SJ162 at 56v rails? I have some pairs I was going to use for a V4 build that I am hoping I could use for the V4H. If not, do you have any 2SK1058/2SJ162 pairs still available?

Thanks!
Greg

Hi Greg.

10n20+p20 is fine.

 

[shaan]

Hi, could we use 0.22ohm resistors instead of the 0.1? It shouldn't have much impact on the functionality from what i can tell.

Yes we can without problem.

 

[katiyar]

Mr Shaan,

Is the amplifier pcb still left with you. I am from India. What is the cost of one bare pcb?

 

[katiyar]

Cost of a pair of MOSFET please.

 

[shaan]

GB Update:

Sadik - 2 PCBs + 4 PAIR MOSFET - SHIPPED
Oracle1 - 2 PCBs + 4 PAIR MOSFET - SHIPPED
J.M.K - 4 PCBS + 4 PAIR MOSFET - SHIPPED
vvs07 - 4 PCBs - SHIPPED
Vunce - 4 PCBs + 4 PAIR MOSFET ( + 4 V4 PCBs ) - SHIPPED
steefdebruijn - 2 PCBS - SHIPPED
Kheon - 4 PCB's - SHIPPED
Neurotica - 2 PCBs - SHIPPED
Arthur -6 PCBS - SHIPPED
Ajit - 2 PRE-ASSEMBLED MODULES - SHIPPING PAID
amitskamal - 1 STEREO KIT - SHIPPING PAID
outtek - 2 PCB + 4 PAIR MOSFET - SHIPPING PAID
craydive - 4 PCBS - SHIPPING PAID
PinkPink - 4 PCBs - SHIPPING PAID
CitizenKane - 4 PCBs - SHIPPING PAID
gaborbela - 2 PCBs - SHIPPING PAID
The Prof - 1 STEREO KIT - SHIPPING PAID
ejno - 2 PCBS - SHIPPING PAID
abanico - 2 PCBs + 4 PAIR MOSFETs - SHIPPING INVOICE SENT
Malvin - 2 PCBs + 4 PAIR MOSFET - SHIPPING INVOICE SENT
hallcon83 - 4 PCBs - SHIPPING INVOICE SENT
smouse - 2 PCBS - NO RESPONSE

Things are moving.

If there is a mistake in the list then please let me know. Thanks everyone for your patience.

 

[shaan]

Mr Shaan,

Is the amplifier pcb still left with you. I am from India. What is the cost of one bare pcb?

Cost of a pair of MOSFET please.

PM sent.

 

[amitskamal]

Hi Shaan,

Please update my request to assembled modules from components + PCB. Already, paid extra cost please check pm.

 

[shaan]

Hi Shaan,

Please update my request to assembled modules from components + PCB. Already, paid extra cost please check pm.

Hi Amit.

Payment received. Your modules are being assembled now.

Thank you.

 

[gaborbela]

I ordered most of the parts for this amp, I only need some 220uF caps to stuff them.