OLD THREAD DAC End by Andrea Ciuffoli

[tassosk]

unless you mod it ;-)

http://www.diyaudio.com/forums/digital-source/153191-m2tech-hiface-usb-spdif-24-192khz-asynch.html
the same is valid with Musiland monitor 01 US that I own.

 

[serph1nia]

Hi Quanghao,

I hope I'm not to late,
i'd like a salas regulator board only. Please pm me price so I can pay with paypal.

Thanks

 

[audiodesign]

some update on schematics and the components list

DAC End 2 - the AD1865N-K with single ended vacuum output stage

 

[quanghao]

Hi Quanghao,

I hope I'm not to late,
i'd like a salas regulator board only. Please pm me price so I can pay with paypal.

Thanks

Yes you can get it! if you like!

 

[dvb projekt]

some update on schematics and the components list

DAC End 2 - the AD1865N-K with single ended vacuum output stage

There are a difference in the part list between the last one here and on your side (Shunt). Which is the actual one?

 

[erwincantona]

There are a difference in the part list between the last one here and on your side (Shunt). Which is the actual one?

dvb-projekt is right...
Will you and Quanghao release the final Part List when the production of PCB has done... It makes us so confuse if there are two different part list...

 

[serph1nia]

Yes you can get it! if you like!

Yes, I would like a salas regulator pcb. Please pm me the price and paypal account

 

[piero7]

quanghao why you don't reply to private messages???

 

[audiodesign]

dvb-projekt,
which parts are different ?

 

[dvb projekt]

The Trimmer & Caps value and the resistors.

 

[quanghao]

The Trimmer & Caps value and the resistors.

hi! DVD-projekt!
I do not change anything, I just standardize the entire map and value!

befor i make PCb, so easy to follow and complete motherboard!
thank!

 

[quanghao]

dvb-projekt is right...
Will you and Quanghao release the final Part List when the production of PCB has done... It makes us so confuse if there are two different part list...

Before I make PCB, I have to standardize all VALUE and the cricuit of all.

SO WILL HAVE SOME VERY SMALL CHANGES. Dont worry about that!
thank

 

[toufu]

Quanghao, do you still have any ad1685 chips or cs8414 chips left? I sent you a PM earlier..

 

[fredlock]

Hi guys,

I checked Digikey about this DAC chip (AD1865) and they're out of stock. Newark only sells it by bulk. 🙁 Where you guys buying your DAC chip? Let me know.

I ask this question earlier but nobody responded.

Quanghao, if you have some AD1865 left for sale then reserve me one too please.

Thanks,
Fred

 

[quanghao]

Hi! i dont sell it ! but i show you on member you can by it:
The price i think is good!
Sieuthiav
SieuThiAV

SieuThiAV

 

[mkollmaier]

Hi Quanghao, i would like to buy the following PCB´s:

1 piece PCB - DAC END
1 piece PCB - Salas Shunt

Is it possible? What is total cost including shipment, paypal feed and so on?

regards, Markus

 

[tassosk]

Hi Andrea,
Is there any posibility to tap I2S signal directly to the board?
Thanks

Ciao Andrea,

I have gear that can output I2S andI'm realy interested.
So is it possible?

Best regards,
Tassos

 

[audiodesign]

No, the AD1865 does not accept I2S signals

 

[tassosk]

Thanks for the reply Andrea.

 

[flocchini]

I did a PayPal for complete set of boards on Saturday.
Thanks for doing this project.

Bob