Ok guys (first name should be nice),
first @obscurus, second Vlad and third KR1sounds...
Khemahl 🙂
@obscurus
please check schematics before layout.
Still some 3D components missing...
Ok, go for Vlad...
Jean-Paul
Wima FKP2 is ok for C2 and C3. I think about Mica because guys from here seem prefer this kind of cap on those place.
Here is my check on the schematic:
- R9, R25 could be CMF55 type.
- T1 = T4 = T6 = 2N5401 need C & E pin swap.
- C5 is 5u6
- Please add 10K resitor // with C26 and C27
Wima FKP2 is ok for C2 and C3. I think about Mica because guys from here seem prefer this kind of cap on those place.
Here is my check on the schematic:
- R9, R25 could be CMF55 type.
- T1 = T4 = T6 = 2N5401 need C & E pin swap.
- C5 is 5u6
- Please add 10K resitor // with C26 and C27
I made a mistake. 10K must // with -38 | GND and -32 | GND. Type = BC PR02
Last edited:
@obscurus
... see attachments...
Wow, it was fast and layout was better than I ever image. Nice layout for the ouput capacitors, I quite like it that way!
Thanks!
@obscurus
How do we proceed?
I can give you the EAGLE binaries?
You downlaod the EAGLE 30 days free demo version; you arrange names and silkscreen informations; do post-processing and order your PCB.
Regards,
Jean-Paul
How do we proceed?
I can give you the EAGLE binaries?
You downlaod the EAGLE 30 days free demo version; you arrange names and silkscreen informations; do post-processing and order your PCB.
Regards,
Jean-Paul
@obscurus
How do we proceed?
I can give you the EAGLE binaries?
You downlaod the EAGLE 30 days free demo version; you arrange names and silkscreen informations; do post-processing and order your PCB.
Regards,
Jean-Paul
Hi,
I think EAGLE binaries will be just fine. I can arrange the files and send it to a local PCB company here with no prob, I already have some exp with EAGLE software. I already ordered the parts needed for this project, will post results when I completed it.
Hello Vlad,
what do you mean?
Regards,
Jean-Paul
Hi Jean-Paul,
It looks good to me. You are a genius in PCB design!
I don't have any photos of the completed amplifier other than the link with the assembled PCB from the page I sent earlier:
http://www.zen22142.zen.co.uk/Circuits/Audio/gempcb.jpg
Just to check - I measured the .png board to be 105mm x 175mm - is yours the same size? Also, will it have silkscreen with components on top?
Thank you very much,
Vlad
Does Eagle spit out Gerber files or will you have to work with a PCB manufacturer that accepts Eagle files?
Tom
Tom
Does Eagle spit out Gerber files or will you have to work with a PCB manufacturer that accepts Eagle files?
Most freestanding PCB programs including Eagle can output Gerber files.
Most programs offered by PCB houses do not, and you have to buy from them.
Last edited:
Most freestanding PCB programs including Eagle can output Gerber files.
For the longest time Eagle did not support Gerber output. I looked at their website and they don't mention Gerber specifically, hence my question.
Tom
Hello Tom,
... see attachment!
I´m using a lot of layout tools in my job (ZUKEN, EAGLE, ALTIUM) and today I can confirm that EAGLE is be able to handle complex jobs (my last job with EAGLE was a custom 5th generation i7 motherboard with active cooling in a 5,25 inch case for military flight usage).
Regards,
Jean-Paul
... see attachment!
I´m using a lot of layout tools in my job (ZUKEN, EAGLE, ALTIUM) and today I can confirm that EAGLE is be able to handle complex jobs (my last job with EAGLE was a custom 5th generation i7 motherboard with active cooling in a 5,25 inch case for military flight usage).
Regards,
Jean-Paul
Attachments
Hello Vlad,
do you use EAGLE? I give you the binaries (schematics and board) and you can modify as desired. Just try and you will see taht its easy...
Regards
Jean-Paul
do you use EAGLE? I give you the binaries (schematics and board) and you can modify as desired. Just try and you will see taht its easy...
Regards
Jean-Paul
No, I don't have this tool unfortunately, so could you please generate the gerbers in addition to the binaries?
Thanks,
Vlad
Thanks,
Vlad
- Status
- Not open for further replies.
- Home
- Design & Build
- Software Tools
- Layouting for free