Hi every body.and thanks members of diyaudio.
I love amplifier .all of them but class D special for me.l try for 3 month work irs2092 amplifier and result equal waste time and money .
First l build schematic in datasheet .i. Use exactly same part in schematic and supply and mosfet but never work.l use +-35 regulate voltage for supply.the problem is one of. The mosfet is all time On and DC voltage -37 volt in terminal speaker.
This schematic
I love amplifier .all of them but class D special for me.l try for 3 month work irs2092 amplifier and result equal waste time and money .
First l build schematic in datasheet .i. Use exactly same part in schematic and supply and mosfet but never work.l use +-35 regulate voltage for supply.the problem is one of. The mosfet is all time On and DC voltage -37 volt in terminal speaker.
This schematic
Attachments
Last edited:
I change value and replace all of resietor and capacitor due DT ,OC ,...
But it not work at all
I change mosfets such as irf3205 irf4227 irf640
But the result is supply voltage in speaker
This is board i make
But it not work at all
I change mosfets such as irf3205 irf4227 irf640
But the result is supply voltage in speaker
This is board i make
Attachments
When i tired from this board i make iraudamp7 and assemble the same part in schematic
This borad iraduamp7
This amp also not work and the same problem.
I search in internt ,forums , topic due irs2092,and replace at least 10 IC irs 2092(i buy from two difrent place to sure they are not fake) and replace mosfets but amp not work
The response result when i connect amp into supply , the negative or some time positve 35 direct. On mosfets and speaker terminal have DC voltage
I changed value resistors CSD ,resistor over current exactly same an1138 but amp not work
I have 2 question
1. Is simple way to run irs2092 with no protectin exist? In other word, how run irs 2092 alone and we sure that work all time work good ever full load ?
2.witch components is sensitve ?and how reduce this sensivity to easy run irs2092 ?it means when we make amp with irs2092 and it work well , by replace component is stil work well?
Thanks
This borad iraduamp7
This amp also not work and the same problem.
I search in internt ,forums , topic due irs2092,and replace at least 10 IC irs 2092(i buy from two difrent place to sure they are not fake) and replace mosfets but amp not work
The response result when i connect amp into supply , the negative or some time positve 35 direct. On mosfets and speaker terminal have DC voltage
I changed value resistors CSD ,resistor over current exactly same an1138 but amp not work
I have 2 question
1. Is simple way to run irs2092 with no protectin exist? In other word, how run irs 2092 alone and we sure that work all time work good ever full load ?
2.witch components is sensitve ?and how reduce this sensivity to easy run irs2092 ?it means when we make amp with irs2092 and it work well , by replace component is stil work well?
Thanks
Attachments
Thanks for reply
What is ceramic decoupler?
If your means capasitor ceramic in out stage
I use .47uF ceramic + 20uH self
Also i use 2.2uF ceramic cap but amp not work
The problem is mosfets contiue On and this due the HO pin (14) is 35volt and this happen also without mosfet and LC filter
What is ceramic decoupler?
If your means capasitor ceramic in out stage
I use .47uF ceramic + 20uH self
Also i use 2.2uF ceramic cap but amp not work
The problem is mosfets contiue On and this due the HO pin (14) is 35volt and this happen also without mosfet and LC filter

Please do not keep starting new threads for this topic. You have started four, all with the same title. Three have been merged into this one.
The voltage power supply +-35
And the out put voltge without R feedback is 32volt
And with R feedback (i change value fro 0 ohm until 200kohm) about 19volt
And the out put voltge without R feedback is 32volt
And with R feedback (i change value fro 0 ohm until 200kohm) about 19volt
I wouldn't mess around changing components randomly as the circuit definitely works as from IR.
The problem is likely a mistake in the build or how its implemented.
Is the power supply, irs2092 and mosfet's well decoupled ?
How did you implement the 12 volt power supply ?
A circuit diagram would help of what you have.
The problem is likely a mistake in the build or how its implemented.
Is the power supply, irs2092 and mosfet's well decoupled ?
How did you implement the 12 volt power supply ?
A circuit diagram would help of what you have.
Last edited:
I use the iraudamp7
And the supply 12 volt from tip35 and diode zener 15 volt from -35 volt
Its genrate -23volt from gnd also 12volt from -35volt negative supply
I sure no mistake in design and assmble part
I check for many times
Whats decoupled power supply for mosfet and irs?
I use +-35 volt that genrate smps from 12volt
And the supply 12 volt from tip35 and diode zener 15 volt from -35 volt
Its genrate -23volt from gnd also 12volt from -35volt negative supply
I sure no mistake in design and assmble part
I check for many times
Whats decoupled power supply for mosfet and irs?
I use +-35 volt that genrate smps from 12volt
Attachments
I use the iraudamp7
And the supply 12 volt from tip35 and diode zener 15 volt from -35 volt
Its genrate -23volt from gnd also 12volt from -35volt negative supply
I sure no mistake in design and assmble part
I check for many times
Whats decoupled power supply for mosfet and irs?
I use +-35 volt that genrate smps from 12volt
Have you been around it with an oscilloscope ?
Are power supply voltages all correct ?
Does reset pin go high and low ?
Does irs2092 put out hi and lo pulses to mosfets ?
The 2092 should have 100nf very close to supply pins.
The mosfets should have 100nf from power supply pins to zero volts very close.
I have designed a few amplifier s using irs2092 and they all work.
So there is a problem in your circuit.
The irs2029 can be a bit funny if you dont have a load on it.
Sometimes it oscillates ok but other times it doesnt.
Sometimes it oscillates ok but other times it doesnt.
I havent oscilloscope.
I measure voltage with voltmeter and i sure +-35
I dont think cap104 help for run irs2092
But i put this caps near supply and mosfet
Dosnt work yet
Thanks for your reply and spend time for this topc
Please load your schem that you make
I measure voltage with voltmeter and i sure +-35
I dont think cap104 help for run irs2092
But i put this caps near supply and mosfet
Dosnt work yet
Thanks for your reply and spend time for this topc
Please load your schem that you make
I havent oscilloscope.
I measure voltage with voltmeter and i sure +-35
I dont think cap104 help for run irs2092
But i put this caps near supply and mosfet
Dosnt work yet
Thanks for your reply and spend time for this topc
Please load your schem that you make
I used datasheet circuit.
At end i success
.the problem in fake ic
By replace it works. Very thanks for nigelwrith7557
I always buy mine from RS Components or Farnell.
When I made my amplifier I could get socketed parts so very easy to change.
good day! I've repaired a turbosound M15 with an irs2092 amp. I have a problem with the startup of the amp. when I put on a bulb on series with the mains input the amp will turn on immediately. but when I plug it directly into 220 mains it won't startup. what could be the problem with this?
- Home
- Amplifiers
- Class D
- IRS2092 problem in start