Hi Ian,
I also haven't received any message for payment.
Thank you.
-coolhead
Just sent, thanks
Hi Ian
I did not receive any invoice, please re-send
Just re-send to the same email address
Thank you for the orders.
All payment invoices were sent. Please let me know if you didn't receive.
or, just send the message to iancanada.mail@gmail.com, so that I can reply with the invoice right away
Thanks again.
All payment invoices were sent. Please let me know if you didn't receive.
or, just send the message to iancanada.mail@gmail.com, so that I can reply with the invoice right away
Thanks again.
Last edited:
Dear iancanada,
i would like to order
1 x I2S FIFO KIT
1 x Dual XO Clock board
1 x S/PDIF Interface Board
Thanks
i would like to order
1 x I2S FIFO KIT
1 x Dual XO Clock board
1 x S/PDIF Interface Board
Thanks
Just sent, thanks
Just re-send to the same email address
Found it in the junk mailbox. I've added the S/PDIF board and two 12" cables and paid total $326.
Thanks
Dear iancanada,
i would like to order
1 x I2S FIFO KIT
1 x Dual XO Clock board
1 x S/PDIF Interface Board
Thanks
Hi ackcheng,
Could you please send your order information to iancanada.mail@gmail.com
Thanks
Dear Ian,
I have sent it before. But I am sending it again just in case. Please kindly also check your spam folder, just in case!
Ackcheng
I have sent it before. But I am sending it again just in case. Please kindly also check your spam folder, just in case!
Ackcheng
Dear Ian,
I have sent it before. But I am sending it again just in case. Please kindly also check your spam folder, just in case!
Ackcheng
Got the payment. No any problem now. Sorry for the confusing.
Regards,
Ian
Hi guys,
Thank you for your payment. I'm trying getting all of the paid orders shipped by next monday. All the boards are ready now, just busy packing.
Hope you enjoy the KIT.
Thank you for your payment. I'm trying getting all of the paid orders shipped by next monday. All the boards are ready now, just busy packing.
Hope you enjoy the KIT.
Hello Ian,
I would like to extend my order with 1 x Dual XO Clock board.
If you didn't shipped my order yet please let me know so I can pay.
Thanks!
Zsolt
I would like to extend my order with 1 x Dual XO Clock board.
If you didn't shipped my order yet please let me know so I can pay.
Thanks!
Zsolt
Hello Ian,
I would like to extend my order with 1 x Dual XO Clock board.
If you didn't shipped my order yet please let me know so I can pay.
Thanks!
Zsolt
Hi Zsolt, Your are lucky. Just about to ship. OK, I'll wait for your payment.
Have a nice weekend.
Ship list Mar 10,2012
Shipped today via Canada Post (without tracking number):
bigpandahk
lll
wktk_smile
vzs
pedefede
zinsula
johnYks
Usually it will take 10 days to 2 weeks, please let me know when you get them.
I need bit more time for other paid orders with tracking nubmer, hopefully I can finish all of them on Monday.
Have a nice weekend.
Shipped today via Canada Post (without tracking number):
bigpandahk
lll
wktk_smile
vzs
pedefede
zinsula
johnYks
Usually it will take 10 days to 2 weeks, please let me know when you get them.
I need bit more time for other paid orders with tracking nubmer, hopefully I can finish all of them on Monday.
Have a nice weekend.
Still didn't receive the invoice for the FIFO kits. Thanks.
My email is bergeron.syl@videotron.qc.ca
My email is bergeron.syl@videotron.qc.ca
Still didn't receive the invoice for the FIFO kits. Thanks.
My email is bergeron.syl@videotron.qc.ca
Sent again. Should be received in you email box now.
Regards,
How do you interface with a TPA BII?
Does anyone know how to interface this with a TPA BII?
Ian gave me some pointers but does anyone know what has to be modified on the BII and connection diagram?
"for a Sabre DAC, because of the internal async clock with DPLL, you have to run it at synchronize mode in order to optimize fifo effect. Some smart guys are figuring out how to achieve this. My fifo could support 1024fs, and the dual xo clock board has a resvered double speed mode with which you can use up to 45.1584M and 49.152M oscillators running all Fs from 44.1K to 192Khz with 256Fs,512Fs and 1024Fs."
Qusp, are you the "smart guy" he was referring to? 😀
Ciao!
Do
Does anyone know how to interface this with a TPA BII?
Ian gave me some pointers but does anyone know what has to be modified on the BII and connection diagram?
"for a Sabre DAC, because of the internal async clock with DPLL, you have to run it at synchronize mode in order to optimize fifo effect. Some smart guys are figuring out how to achieve this. My fifo could support 1024fs, and the dual xo clock board has a resvered double speed mode with which you can use up to 45.1584M and 49.152M oscillators running all Fs from 44.1K to 192Khz with 256Fs,512Fs and 1024Fs."
Qusp, are you the "smart guy" he was referring to? 😀
Ciao!
Do
it would appear i am, thanks for the inverted commas btw 😀
have you got the right clocks? you need to disable the BII onboard clock by removing its power, then feed MCLK from the fifo reclock board to X1 on the 9018. you should do this as neatly as possible, you could use twisted pair, or a u.fl connector with either a oe sided cable with the connector on the fifo side and soldered on the other, or by finding a suitable place to solder in a u.fl socket on the BII board. i'm not working with the BII, so probably someone who is playing with syncronous clocking on that may be better suited to show where theyve done it. you could have a look in the waveIO thread, we were discussing it in there a while ago
have you got the right clocks? you need to disable the BII onboard clock by removing its power, then feed MCLK from the fifo reclock board to X1 on the 9018. you should do this as neatly as possible, you could use twisted pair, or a u.fl connector with either a oe sided cable with the connector on the fifo side and soldered on the other, or by finding a suitable place to solder in a u.fl socket on the BII board. i'm not working with the BII, so probably someone who is playing with syncronous clocking on that may be better suited to show where theyve done it. you could have a look in the waveIO thread, we were discussing it in there a while ago
it would appear i am, thanks for the inverted commas btw 😀
have you got the right clocks? you need to disable the BII onboard clock by removing its power, then feed MCLK from the fifo reclock board to X1 on the 9018. you should do this as neatly as possible, you could use twisted pair, or a u.fl connector with either a oe sided cable with the connector on the fifo side and soldered on the other, or by finding a suitable place to solder in a u.fl socket on the BII board. i'm not working with the BII, so probably someone who is playing with syncronous clocking on that may be better suited to show where theyve done it. you could have a look in the waveIO thread, we were discussing it in there a while ago
Thanks!
I'm still waiting for my WaveIO board but I am really interested in this project. I'll go and read this part of the thread I have obviously missed!
What is your comment on SQ or difference between just WaveIO + DAC and WaveIO + FIFO + DAC?
Edit : Found it on post 209 - 220 of this thread http://www.diyaudio.com/forums/digi...-based-asynchronous-usb-i2s-interface-21.html in case it can help anyone..
Ciao!
Do
Last edited:
What is your comment on SQ or difference between just WaveIO + DAC and WaveIO + FIFO + DAC?
Way off topic for the GB thread but ... qusp and I could try that in a month or so if you really want to know.
qusp doesn't have a waveio, but I will soon (though qusp does already have just a few options for usb audio devices!). I don't have a FIFO kit, but qusp does already. We're only a reasonably short drive apart, depends how well our respective schedules line up and how badly we both want to know the answer really!
to clarify as well, i do have ermm 2 x buff II, 2 x Ackodac AKD12P and 1 x AKD12 😱 , but i'm only at this stage playing with syncronous operation with the ackodacs, as the buffs are part of my transportable dac/headamp research which i'm at this stage running async, although i'm toying with the idea of building up one of these to install in it and running synchronous that too, but no fifo.
DX100 eat me 😀
waveIO will be limited to 96k with syncronous mode unless the OSF is disabled even with the NDK. you need to double the clock speed to get 192 and then divide/2 for waveIO
DX100 eat me 😀
waveIO will be limited to 96k with syncronous mode unless the OSF is disabled even with the NDK. you need to double the clock speed to get 192 and then divide/2 for waveIO
Last edited:
Still pcbs available?
I need to reduce jitter from my CD player (S/PDIF) & Hiface USB or Musiland Monitor 0.3US (I2S mod) as players how can integrate for BIII+4 channel SPDIF input+Sidecar combo? Can support 24BIT/352.8kHz for Musiland Monitor 03.US (I2S mod)?
I need to reduce jitter from my CD player (S/PDIF) & Hiface USB or Musiland Monitor 0.3US (I2S mod) as players how can integrate for BIII+4 channel SPDIF input+Sidecar combo? Can support 24BIT/352.8kHz for Musiland Monitor 03.US (I2S mod)?
Last edited:
Hi guys,
All the KIT with tracking number to the States were shipped yesterday. Tracking numbers were updated by PayPal.
However Canada Post has problem with tracking number to the other part of the world. I was told have to go either normal air mail (with $9USD refund), or go with express mail which will double the shipping. I apologize about that. I like Canada except the post office 🙁 . please let me know what your choice.
All the KIT with tracking number to the States were shipped yesterday. Tracking numbers were updated by PayPal.
However Canada Post has problem with tracking number to the other part of the world. I was told have to go either normal air mail (with $9USD refund), or go with express mail which will double the shipping. I apologize about that. I like Canada except the post office 🙁 . please let me know what your choice.
- Home
- Group Buys
- Ian asynchronous I2S and S/PDIF FIFO KIT group buy