GB For Salas SSLV1.3 Ultra-BIB

[michip]

I see a 2 there, not 1?

OPPS!!
You are right I made a mistake.
I have updated.
Thanks

 

[zgtc]

OPPS!!
You are right I made a mistake.
I have updated.
Thanks

you're welcome 😀

 

[stephengrenfell]

Added myself for 1 set boards plus 1 each +ve -ve minikits.

Thanks for doing this.

Stephen

 

[ktham]

Requested two sets of boards. Also require two +5V minkits, two +15V minikits and two -15V minikits. Thank you and have a pleasant evening.

 

[sjalloq]

Thanks for organising TeaBag.

I've gone for a few kits with 2 positive boards required for 5V.

 

[fedde]

@Teabag. I noticed that numbers were written on the PF5102 JFETs. I presume this is IDSS? Was this only done as preselection for 5V kits? Or can I optimize the circuit performance by putting lower IDSS parts on specific locations in the circuit (J1,J2,J3)?

 

[Tea-Bag]

@Teabag. I noticed that numbers were written on the PF5102 JFETs. I presume this is IDSS? Was this only done as preselection for 5V kits? Or can I optimize the circuit performance by putting lower IDSS parts on specific locations in the circuit (J1,J2,J3)?

So, in order to yield some lower IDSS JFETs for those using 5V output, I had to measure a whole bunch. Some of you simply got the leftovers from that output.
There is no benefit of using different IDSS elsewhere. If not 5V, then they all can be high or low IDSS.

 

[fa02]

Signed up. Thank you very much for the group buy.

 

[axelcs]

Dear Teabag,
tried to add my wishes in the gb document, doesn´t work.
I would like to get 3 positive kits and 2 negative kits (+12V, -12V).
Axel

 

[guneyt]

Thank you Teabag.. Signed up for 1 board plus 1 positive and 1 negative kit.

 

[tony hunt]

I am new here and have signed for one board to get me started. Thank you Teabag for organising this group-buy, I appreciate the time involved.

 

[Johnny2Bad]

Well, I *think* I signed up. 2x boards 15V +/- No minikits

 

[axelcs]

signed in for 3 +minikits and 2 -minikits, thanks a lot, Teabag
Axel

 

[euro21]

Signed for PCB and 2x +5V, 1x -5V MiniKit.

 

[brownaye]

signed up 2 pcb sets 24v

signed up 2 pcb sets 24v with 2 pos and 2 neg minikits. Thank you!

 

[Tea-Bag]

Salas Boards GB Ends 12/9/2018

The last GB for the end of the year has started and will close out on 12/9/2018.
If you have signed up on spreadsheet previously, I should have private messaged you by now on next steps.


So, to get in on GB please sign up on spreadsheet and then private message me. Any questions, private message me.

 

[alopa]

I signed up on the spread sheet and messaged you. Alopa

 

[Tea-Bag]

Salas Boards GB Ends 12/9/2018

GB Ends for Salas Boards on December 9, 2018.
Please pay invoices by the end of that day.
If you have not gotten an invoice, please private message me.
This GB will close in 5 more days.

Tea

 

[Stéphane B]

Hello Tea-Bag, payment sent ! 🙂

 

[alopa]

hello tea bag . I am ALOPA . I have not received your email requesting payment. for 2018 Salas Boards GB #2 . I have requested 1 PCB and two + 5 volt parts kits and one minus 5 volt parts kit. Please send me the payment email so I can pay by PayPal.