You are welcome guys and thanks for the confirmation of receipt
.
Yes , more than 200 of rectifier PCBs distributed around the world🙂 , still ran short and couldnt include in some the packages.
apologies to guys who didnt get it😱.
regards
Prasi

Yes , more than 200 of rectifier PCBs distributed around the world🙂 , still ran short and couldnt include in some the packages.
apologies to guys who didnt get it😱.
regards
Prasi
My CRCRC board is up and running, powering the M2X now.
Too eager to populate the board and end up making a mistake on one board for not leaving some air gaps for those 3W resistors.
Luckily those resistors are not hot during operation.
Too eager to populate the board and end up making a mistake on one board for not leaving some air gaps for those 3W resistors.
Luckily those resistors are not hot during operation.
Hello Meanie,
Congratulations on successful build
.
could you please post some pics?
regards
Prasi
Congratulations on successful build

could you please post some pics?
regards
Prasi
I just checked the Google sheet and tracked my item number... it says delivered in France.
I am in Germany though, and the correct adress is given in my Paypal?
Can you please check?
I am in Germany though, and the correct adress is given in my Paypal?
Can you please check?
Hello stixx,I just checked the Google sheet and tracked my item number... it says delivered in France.
I am in Germany though, and the correct adress is given in my Paypal?
Can you please check?
There was a mistake from my side to have shipped your package to France.
I have asked the gentleman in France to forward the package to you and he has kindly agreed for the same.
Regarding this, I had written an email to you from analog design email id , dated 10th April. Kindly go through the same.
Once again, I am sincerely sorry for my mistake and hope you will get the boards at the earliest.
Regards
Prasi
My CRCRC board is up and running, powering the M2X now.
Too eager to populate the board and end up making a mistake on one board for not leaving some air gaps for those 3W resistors.
Luckily those resistors are not hot during operation.
Congratulations, even my M2X amp boards built and ready for the PSU. Was thinking of using these CRCRC boards. Let me know the parts that you have used as I have some 15000uf caps with me so either a dual mono like yours or a single psu will be using. I think these psu boards have too many options to try and I was thinking of using outboard bridge rectifiers instead of onboard diodes section. Prasi suggested in one of the posts to cut the pcb marked near the section of the diodes. The board is so nice that finding difficulty to cut it and rather built it fully with diodes.
So please let me know the parts list that you used including the R's to get the right DC out for your M2X amp.
Thanks
Hello StixxI just checked the Google sheet and tracked my item number... it says delivered in France.
I am in Germany though, and the correct adress is given in my Paypal?
Can you please check?
No worries, I received your package in the last week and was posted last Saturday and should be leaving for you today.
Prasi with all these shipments was wrong but warned me immediately.
Regards
Hi meanie,My CRCRC board is up and running, powering the M2X now.
Too eager to populate the board and end up making a mistake on one board for not leaving some air gaps for those 3W resistors.
Luckily those resistors are not hot during operation.
If you have bought your parts through Mouser, ir will be great if you could share it as a project BOM. TIA.
I do buy from Mouser, as I have few projects on going, my BOM is a mess.
Let me recompile those for CRCRC, and I will post to share soon.
Let me recompile those for CRCRC, and I will post to share soon.
I do buy from Mouser, as I have few projects on going, my BOM is a mess.
Let me recompile those for CRCRC, and I will post to share soon.
Thank you.
Hello Stixx
No worries, I received your package in the last week and was posted last Saturday and should be leaving for you today.
Prasi with all these shipments was wrong but warned me immediately.
Regards
Merci projet16!
Pas de soucis, je vais attendre mon petit paquet... 🙂
Thank you Prasi for the heads up!
Hi meanie,
If you have bought your parts through Mouser, ir will be great if you could share it as a project BOM. TIA.
Hello ED,
I have posted a BOM in post 1 of the thread with mouser part nos. Please refer the same according to your suitability.
You can make a new column in that excel file and post your part nos actually used.
Regards
Prasi
Last edited:
- Home
- Group Buys
- GB: CRCRC PSU