No problem Carlos, these things happen. The boards look great by the way, I couldn't see the pictures the other day as I was at work and the work filter blocks photo's. Pass on our well wishes to Mitchel that he hopes feeling better soon.
Luke
Luke
As sson he feel a little bit better to move his body, i'm sure
he will proceed the packing and delivery.
regards,
Carlos
he will proceed the packing and delivery.
regards,
Carlos
I'm already feeling better, thanks God.
Thank you Carlos for your worry.
I believe I can start packing tomorow and shipping by friday.
Thank you Carlos for your worry.
I believe I can start packing tomorow and shipping by friday.
Hallo,
Will this Amplifier working with 2 x 42 volt 2000Va torroids (total 63volt I think) see my signature?
I remove the Zappulse 2.3SE and insert the DX Blame MKII Supercharged.
Rudy
Will this Amplifier working with 2 x 42 volt 2000Va torroids (total 63volt I think) see my signature?
I remove the Zappulse 2.3SE and insert the DX Blame MKII Supercharged.
Rudy
Last edited:
Yes BMW850, it can work without any modification
58 volts i think you gonna have as result of rectification and filtering.
No problems about it.
I do think we do not have boards anymore... but post your order, including quantity of boards and what boards you want.... this way, we gonna know if it is interesting to run a second round or not.
Of course you can etch boards by yourself, reason why we have concentrated layouts here:
at www.dx.kinghost.net
*
regards,
Carlos
58 volts i think you gonna have as result of rectification and filtering.
No problems about it.
I do think we do not have boards anymore... but post your order, including quantity of boards and what boards you want.... this way, we gonna know if it is interesting to run a second round or not.
Of course you can etch boards by yourself, reason why we have concentrated layouts here:
at www.dx.kinghost.net
*
regards,
Carlos
PCBs are being shipped today! 🙂
PCBs are being shipped today! 🙂
PCBs are being shipped today! 🙂
An externally hosted image should be here but it was not working when we last tested it.
I have just arrived from the Postal Office.
All envelopes were shipped by registered priority mail. This way, we can keep track of the packages.
Our mail service herein Brazil is not fast, specially on Christmas time. I ask you all to knidly wait about 3 keeks to receive the boards. Some countries, like Italy and Israel, are known to take longer.
By now, I can only track the packages through Brazilian website. Once the packages enter the foreign country, you will be able to track it through your local post office website.
If you would like to have your tracking code, please PM me.
All envelopes were shipped by registered priority mail. This way, we can keep track of the packages.
Our mail service herein Brazil is not fast, specially on Christmas time. I ask you all to knidly wait about 3 keeks to receive the boards. Some countries, like Italy and Israel, are known to take longer.
By now, I can only track the packages through Brazilian website. Once the packages enter the foreign country, you will be able to track it through your local post office website.
If you would like to have your tracking code, please PM me.
I would like to invite you to read the Supercharged thread from the first to the last
post.... in special the last posts will be helpfull to you to assemble..also to order transformers or to check the ones you have at home.
This amplifiers does not accept higher voltages nor higher power in the transformer...as output transistors are the limiting factor..so.... take care about the transformer..they can be smaller than the values suggested..but not bigger.
The transformer power selection, also voltage, was made in order to protect the output against excesses of power.... so, transformer is the limiting tool..need a good selection.
Transistors are only two pair...so..they are into the limits when operating 4 ohms...and cannot operate with lower impedance anyway... was made this way to reduce cost to builders...but, a mistake into the transformer power can allow the amplifier to reach easy 300 watts RMS... and this may destroy the output transistor...so.... the small transformer was selected in order to limit the Supercharged output power to 200 - 240 watts RMS only.
http://www.diyaudio.com/forums/soli...mkii-supercharged-release-32.html#post2405200
regards,
Carlos
post.... in special the last posts will be helpfull to you to assemble..also to order transformers or to check the ones you have at home.
This amplifiers does not accept higher voltages nor higher power in the transformer...as output transistors are the limiting factor..so.... take care about the transformer..they can be smaller than the values suggested..but not bigger.
The transformer power selection, also voltage, was made in order to protect the output against excesses of power.... so, transformer is the limiting tool..need a good selection.
Transistors are only two pair...so..they are into the limits when operating 4 ohms...and cannot operate with lower impedance anyway... was made this way to reduce cost to builders...but, a mistake into the transformer power can allow the amplifier to reach easy 300 watts RMS... and this may destroy the output transistor...so.... the small transformer was selected in order to limit the Supercharged output power to 200 - 240 watts RMS only.
http://www.diyaudio.com/forums/soli...mkii-supercharged-release-32.html#post2405200
regards,
Carlos
Last edited:
I am interested in 2 Amplifier boards and 2 PSU boards, if you have any more or planning another group buy.
I am in the US of A
I am in the US of A
I would be interested in 2 amp, 2 psu and 2 LS protection if still available, pls PM, I am in Canada
Mitchel is tracking this thread...he will take notes about the ones wants
He may be waiting a reasonable quantity of people..this way he will be able to keep the price the way it was in the first round.
Here you have some pictures.... your boards are on their way to your home...soon you gonna have them.
regards,
Carlos
He may be waiting a reasonable quantity of people..this way he will be able to keep the price the way it was in the first round.
Here you have some pictures.... your boards are on their way to your home...soon you gonna have them.
regards,
Carlos
Attachments
Here you have more detailed instructions prepared by Mitchel
Here you have Mitchel's link:
http://www.nabucoeletronica.com.br/dx/files/Esquema-universal-english.pdf
This is a link for higher resolution images.
All informations will be also at Greg site:
Greg's Web Site
regards,
Carlos
Here you have Mitchel's link:
http://www.nabucoeletronica.com.br/dx/files/Esquema-universal-english.pdf
This is a link for higher resolution images.
All informations will be also at Greg site:
Greg's Web Site
regards,
Carlos
Attachments
Last edited:
My boards arrived in UK today. Nice quality, many thanks Miguel and Carlos.
I'm still trying to decide which version to build. Probably either ES or ST, I take it the ES sounds better but the ST is more stable?
Is it possible to provide a list of components that are directly in the signal / audio path?
Thanks again guys 🙂
I'm still trying to decide which version to build. Probably either ES or ST, I take it the ES sounds better but the ST is more stable?
Is it possible to provide a list of components that are directly in the signal / audio path?
Thanks again guys 🙂
For you too Aman
Be happy next year...and visit videos from Brasil.....from Rio de Janeiro...down this page, in the signature line.... links to Rio de Janeiro.
Enjoy.
regards,
Carlos
Be happy next year...and visit videos from Brasil.....from Rio de Janeiro...down this page, in the signature line.... links to Rio de Janeiro.
Enjoy.
regards,
Carlos
- Status
- Not open for further replies.