• Disclaimer: This Vendor's Forum is a paid-for commercial area. Unlike the rest of diyAudio, the Vendor has complete control of what may or may not be posted in this forum. If you wish to discuss technical matters outside the bounds of what is permitted by the Vendor, please use the non-commercial areas of diyAudio to do so.

DAC-END R (ES9018) full assembled board

Status
Not open for further replies.
Jump to Latest
#1,002
rredline Would be highly likely to order this together with the DAC sheild.:)[/QUOTE said:
Here is an image of the shield, it is about to be completed
Click to expand...
 

Attachments

  • shield DAC 32.1.jpg
    shield DAC 32.1.jpg
    103.7 KB · Views: 611
  • shield DAC 32.2.jpg
    shield DAC 32.2.jpg
    77.8 KB · Views: 590
#1,010
Hi Quanghao,

Is it possible to order/ship the DAC shield together with the new discrete output stage ?

When will the new discrete output stage be ready for shipment ?

@Andrea:
Have you been able to compare the new discrete output stage with the LL1684 ?

Regards,
Danny
 
#1,012
Hi Andrea,
I have tried the USB Amanero input with Foobar (Windows XP):
- When I turn the DAC on, the display shows "44Khz", "USB link_". "LOCK".
- Then, when I start reading with Foobar, the display always shows "95KHz" even if sample rate is 44.1 kHz or ... or 192 kHz in Foobar. The signal reaches to the amplifier in each case.
 
Last edited:
#1,013
I've put all the DAC shield.
Material: Copper-Nickel-Zinc
alloy C7521

This is a gift for all of you!
it looks like this picture
Some days I'll get it, and I will send it to everyone. However, you have to pay shipping , about 5 to 10$ .

You do want it, please let me know! Thank you

1. sipo75
2. Domi_78
3. bobkojek
4. Erlend Sæterdal
5. danielkol*2
7. kmajjo * 6
.......
 
#1,016
Domi_78 said:
Hi Andrea,
I have tried the USB Amanero input with Foobar (Windows XP):
- When I turn the DAC on, the display shows "44Khz", "USB link_". "LOCK".
- Then, when I start reading with Foobar, the display always shows "95KHz" even if sample rate is 44.1 kHz or ... or 192 kHz in Foobar. The signal reaches to the amplifier in each case.
Click to expand...

Have you installed the Amanero driver ?

Are you using the standard Direct Streaming output mode on Foobar2000 ?
 
#1,017
quanghao said:
the new discrete output stage

please waite me, i need finis sent all dac!

thank
Click to expand...

Hi Quanghao,

I have the same questions as Danny. I would love to have the shield installed before shipping of my DAC.
If possible, can you also include the new discrete output stage?

I am not sure if I understand your post. Do you first send all the DACs and after that send the output stage or can you install it in the DAC, before sending?

Cảm ơn bạn rất nhiều! 🙂
 
#1,018
MattMax said:
Hi Quanghao,

I have the same questions as Danny. I would love to have the shield installed before shipping of my DAC.
If possible, can you also include the new discrete output stage?

I am not sure if I understand your post. Do you first send all the DACs and after that send the output stage or can you install it in the DAC, before sending?

Cảm ơn bạn rất nhiều! 🙂
Click to expand...

HI!

DAC all ready.

The dac kit ready
I waited a few days shield

I send all DAC + Kit and shields for you!

So you would be waiting!

IV-The new design is in the design layout, I need time. Hope your understanding!
 
Status
Not open for further replies.
Top Bottom