They've been out of stock for about a year now ... just order direct.
https://www.modushop.biz/site/
On Nov. 2 Jason posted on another thread that they were supposed to be available in "a few days." If so, they should show up any time. At least that's what I'm hoping. 🙂
That's right! diyAudio's new store will open in a week or two. Do please watch out for that.
But if you can't wait any longer, you can order through this form:
Hifi2000 order form
But if you can't wait any longer, you can order through this form:
Hifi2000 order form
My fault entirely. Unfortunately since leaving Italy, where I had the new store in an "almost ready to launch" state, I've grossly underestimated my free time. Other than some long stretches during flights I haven't had any free time of extended duration to get work done that requires serious concentration.
I'm in the middle of a very heavy mix of travel, relocation and events as I shift back to living in Australia, have been for months, and will be until November 24. In the midst of this I'm trying to make time to get the new store launched and it's currently my #1 priority. I apologise to everyone for ever shifting launch date for the new store - since Nov 2 I haven't had time to take care of anything other than putting out urgent fires.
If you want a deluxe chassis in the meantime, they cannot be ordered directly from the Hifi2000 website. I don't want anyone waiting any longer, so please feel free to using this special form to order one, and I believe you can order one now. I've already pre-ordered a large amount of 4U and 5U chassis and they're now sitting at Hifi2000 waiting for the new store to be launched, pending some minor adjustments to the back panel. I'm hoping to have the new store launched within the next week, it all depends how much time I'm able to carve out. Realistically, based on my track record, this could blow out by a few weeks. After November 24 I'll have plenty of time to do serious development, but I hope I can pull a few all nighters along the way and at least get the store "soft launched" well before then. Again, apologies for all the delays and thanks to everyone for their support.
I'm in the middle of a very heavy mix of travel, relocation and events as I shift back to living in Australia, have been for months, and will be until November 24. In the midst of this I'm trying to make time to get the new store launched and it's currently my #1 priority. I apologise to everyone for ever shifting launch date for the new store - since Nov 2 I haven't had time to take care of anything other than putting out urgent fires.
If you want a deluxe chassis in the meantime, they cannot be ordered directly from the Hifi2000 website. I don't want anyone waiting any longer, so please feel free to using this special form to order one, and I believe you can order one now. I've already pre-ordered a large amount of 4U and 5U chassis and they're now sitting at Hifi2000 waiting for the new store to be launched, pending some minor adjustments to the back panel. I'm hoping to have the new store launched within the next week, it all depends how much time I'm able to carve out. Realistically, based on my track record, this could blow out by a few weeks. After November 24 I'll have plenty of time to do serious development, but I hope I can pull a few all nighters along the way and at least get the store "soft launched" well before then. Again, apologies for all the delays and thanks to everyone for their support.
Last edited:
Jason, thanks for keeping us posted and all your effort in making this happen.
Good luck with your move!
Good luck with your move!
Haven't had a moment to touch on any diyAudio work since my last message above, so November 24th it will be before I can resume work on this. Hope to have the store launched at the end of that week.
Finally back in civilisation, have a clear schedule and can focus exclusively on getting the new store up. The whole thing hinges on 2 months of coding which was "almost" completed a month ago but as I've had to explain, I set up an impossible sequence of commitments in between. Apologies to everyone waiting. It'll be up real soon (I'm going to say this Friday, and if not, at the latest the following Friday).
Progress over the last few days has been smooth and I've now re-coded all the work that I lost in my hard drive crash. There's still quite a bit to do but I'm confident we'll go live before the end of next week.
Jason, the chassis that I would like to use have the following specs:
Galaxy 3U, 330x280, thin front panel
Galaxy 3U, 230x280, thin front panel
Advantage: Transformer fits (3U), Controls fit on front (3mm), And quasi heatsink is big (3Ux280)
Galaxy 3U, 330x280, thin front panel
Galaxy 3U, 230x280, thin front panel
Advantage: Transformer fits (3U), Controls fit on front (3mm), And quasi heatsink is big (3Ux280)
Quick question to Jason or a moderator 'in the know'; does one need to secure permission to design around the UMS presented in the document linked to in the store?
I'm thinking it might be needed nice to port a modular design to the stores chassis. Just thought I'd check rather than assume anything.
I'm thinking it might be needed nice to port a modular design to the stores chassis. Just thought I'd check rather than assume anything.
No permission necessary... it's beneficial to all if designs fit the UMS!!
What are you making?
What are you making?
I think it might be nice to have a 'SlewMaster' based OPS that fits the UMS for those who have or are willing to buy the DIYA Store chassis.
Finally! 🙂 But seriously... it was always the intention to have people leverage it to make designs more accessible. Please go right ahead. We'd love to have people using the UMS for their own projects.
BTW - store development update: Things are going well, the path has been long, many thousands of lines of code have been written and much data wrangled. Most of the Hifi2000 clan are on holiday this week and back next Monday, which seems to co-incide perfectly with when I think we'll be live with the new store.
Last edited:
Could anyone tell me what size fuses are used in the Schurter switch/fuse holder included in the chassis back panel parts kit? Or the part number of the fuse holder? If I have the latter, maybe I can search for the spec? TIA - Pat
Store update: The new store is now finished and will go live as soon as we have a green light from FedEx in regards to a specific logistics issue. First chassis will ship January 7th using the new system. We have some other new goodies ready to go as well...
There's nothing I'd like more than to open it up. However I don't want to have to ask customers to change their orders if we need to adjust something. We were hoping to hear back yesterday, but now it's Christmas I doubt we'll hear back until Monday. I'll post here before posting anywhere else when it does open up.