If the commands also exists for dam1021 - no differences.
//
Obviously there is a difference as the unfolding discussion on dam1021 blog just discovered.
Can you please confirm that you can change polarity in dam1121 during playback without power cycling dam1121.
Just wanted to be sure.
This does not work on 1121, unfortunately. At least not mine.
One would have thought the firmware the same?
This does not work on 1121, unfortunately. At least not mine.
One would have thought the firmware the same?
Just wanted to be sure.
This does not work on 1121, unfortunately. At least not mine.
One would have thought the firmware the same?
All dam1121 have same firmware so it do works. You just need to figure out what you do wrong....
Well,
I can change filters. Just figured out how simple that is, outside of umanager.
Just turned the computer on again to make sure I had not done something wrong.
I get a response to all four F settings but after I press "enter" after typing in PI or PN there is nothing displayed as there is with the F settings.
Is this how it works with P settings?
I can change filters. Just figured out how simple that is, outside of umanager.
Just turned the computer on again to make sure I had not done something wrong.
I get a response to all four F settings but after I press "enter" after typing in PI or PN there is nothing displayed as there is with the F settings.
Is this how it works with P settings?
Perhaps this is a typo?Just wanted to be sure.
This does not work on 1121, unfortunately. At least not mine.
One would have thought the firmware the same?
You have a DAM 1021 (correct?) and noticed that some things that work on the DAM 1121 do not on the 1021.
zfe, you are correct.
Sorry for another stupid post. Sad thing is I went to the SOEKRIS website to make sure I would type the correct number. Went ahead and typed the wrong number, anyway. Too early for cocktails, at least that would be a better excuse.
Sorry, SOEKRIS.
Sorry for another stupid post. Sad thing is I went to the SOEKRIS website to make sure I would type the correct number. Went ahead and typed the wrong number, anyway. Too early for cocktails, at least that would be a better excuse.
Sorry, SOEKRIS.
I have a big question that still confuses me..
what are these for
VCC5D Digital Power 250 350mA
VCC5A Analog Positive Power 20 50mA
VEE5A Analog Negative Power 20 50mA
now please give me a clarity that the VCC5A and VEE5A are these the ones which powers the Ladders and vref?
VCC5D all the FPGA and the digital circuits?
can I use about 6V for the VCC5A and VEE5A?
what are these for
VCC5D Digital Power 250 350mA
VCC5A Analog Positive Power 20 50mA
VEE5A Analog Negative Power 20 50mA
now please give me a clarity that the VCC5A and VEE5A are these the ones which powers the Ladders and vref?
VCC5D all the FPGA and the digital circuits?
can I use about 6V for the VCC5A and VEE5A?
I have a big question that still confuses me..
what are these for
VCC5D Digital Power 250 350mA
VCC5A Analog Positive Power 20 50mA
VEE5A Analog Negative Power 20 50mA
now please give me a clarity that the VCC5A and VEE5A are these the ones which powers the Ladders and vref?
VCC5D all the FPGA and the digital circuits?
Correct.
can I use about 6V for the VCC5A and VEE5A?
That would be beyond specs and the over voltage protection diodes might kick in.... And there is no advantage by supplying 6V.
Correct.
That would be beyond specs and the over voltage protection diodes might kick in.... And there is no advantage by supplying 6V.
So the digital ground and analog ground are separated?
dam1121 uManager Rev 1.08 20160523 FPGA Rev 1.08 Press ? for help.
# set
Conspeed = 9600
Volume = -25
Filter = Linear
Mode = Bal-Left
Needed to set the conspeed to 9,6 in oreder for the yet not connected BT->COM receiver to work.
Close now for first channel.
//
# set
Conspeed = 9600
Volume = -25
Filter = Linear
Mode = Bal-Left
Needed to set the conspeed to 9,6 in oreder for the yet not connected BT->COM receiver to work.
Close now for first channel.
//
Attachments
Sören, I experience quite a bit lower level compared to running it in standard stereo. I was expecting the opposite.
//
//
- Home
- Source & Line
- Digital Line Level
- Building with the Soekris dam1121