AZ OLED setup kits for Soekris dam1021/1121 control

[hirscwi]

Thank you.

 

[vipulpatel83]

Do we need to connect the Rotary encoder mandatorily with the Display? Just connecting the Display without the Rotary encoder, the display is not lightening up.

 

[vipulpatel83]

For me even after connecting the Rotary Encoder, OLED display is not working. Any suggestions?

 

[audiozen]

For me even after connecting the Rotary Encoder, OLED display is not working. Any suggestions?

pm, all kits were tested before shipment. please send some pictures or videos to me.

 

[vipulpatel83]

pm, all kits were tested before shipment. please send some pictures or videos to me.

I have PMed you. All is working now after I debugged and found a loose connection near 6VAC taro side. Thanks!!

 

[audiozen]

I have PMed you. All is working now after I debugged and found a loose connection near 6VAC taro side. Thanks!!

Cool！

 

[jacek_k_wawa]

The kits for dam1941 is still under development, and there is no detail schedule for release. I will update my post in time.

Any update on this?

 

[CroweMagnon]

Audiozen, I just sent a PM purchase request. Thank you.

 

[audiozen]

Audiozen, I just sent a PM purchase request. Thank you.

PM😀

 

[PKI]

Did I solder the encoder on the wrong side of the PCB?

Hi do mind sharing what chassis is that?

 

[CroweMagnon]

Payment sent, thank you

 

[Pegasus123]

Maybe I missed it but which switch position is buffered?

Left/Left
Left/Right
Right/Right
Right/Left

I assume based on the attached screenshot that it's Left/Right

 

[daniel4381]

I am using AZ OLED lite kits with dam1021. My setup is with a raspberry pi, and using Moode Audio. It is working perfectly, but it does not show up "DSD" once dsd file is played, instead it shows "PCM 192khz". Another observation is once I play flac file it is always " PCM 44.1", where as my Gustard x26 DAC shows some of those files are 96 khz or like this. Is it a problem? Image showing a dsd playback, this file shows 2.82mhz sample rate in Gustard.

 

[daniel4381]

Double post

 

[audiozen]

Both switches are inward, RAW

Both switches are outward，BUFF

Maybe I missed it but which switch position is buffered?

Left/Left
Left/Right
Right/Right
Right/Left

I assume based on the attached screenshot that it's Left/Right
View attachment 805028

 

[audiozen]

Please check the settings of your raspberry pie player soft，Az1021 will not make any judgment, only display the status of dam1021.

I am using AZ OLED lite kits with dam1021. My setup is with a raspberry pi, and using Moode Audio. It is working perfectly, but it does not show up "DSD" once dsd file is played, instead it shows "PCM 192khz". Another observation is once I play flac file it is always " PCM 44.1", where as my Gustard x26 DAC shows some of those files are 96 khz or like this. Is it a problem? Image showing a dsd playback, this file shows 2.82mhz sample rate in Gustard.

 

[janvlk]

After testing, AZ Lite can be used in 1941, but the input of dam1941 is different from dam1021,so there is a problem with input selection. The firmware of AZ lite will be modified later for dam1941.

Audiozen, is AZ lite firmware already modified for dam1941? I would like AZ lite for dam1941 buy.

 

[azer31]

Hello audiozen

I am very satisfied with the kit
I just have a problem with the remote control

I place the device in programming mode I have the indication volume +

but nothing happens? to the measurement on the ir connector I have
out = 4.9V
0V = 0V
5V = 5.01V

measurement with ir sensor not installed

an idea

thank you

 

[nautibuoy]

Does the lite version work with the DAM1921/1941 boards yet?

 

[bsy020]

The DAM 1021 SK lite has a transformer with two isolated secondaries. Is it possible to feed it with an external transformer with a single secondary?
Thanks