Yes I did.. But my son is sleeping now.. so I can only listen to very low level.. I also changed the tweeter cap for 2.2uf..
I enjoy trying differnet caps and XO points so exact schematic would be boring 😉
Thanks for the help.. 🙂
I did the same thing just to try.. I also agree L-pad is the way..
Bucherout did also bring aprovements.. well worth trying.. 😉
Zen Mod.. did you recive Beta drivers?
Yunick said:
not yet ;
I don't need them personally , and boy who need them prolonged that project a little
Would be nice to hear your oppinion on them.. 🙂
Btw... What do you listen trou these days? How do your setup look like?
I remember somthing with toobz putting ut 250mW...
Zen Mod said:
Aghh....
Dunno who's that, but I prolonged my project a little...
There's a guy that was supposed to cut those baffles for me, and then he said.."sorry, I can't cut at such an angle !!" (side wings-look at Visaton No box project)
Then, the lack of out-of-job-free-time prevented me from lookin' for another carpenter. Hopefully it will be this weekend...
Vix
Yunick said:
well,Yunick ,something as on attached picture ........
Pioneer PD8500 (stock) feeded from headphone output to quickie tweaked venerable ECL82 SE stereo amp, gutted from ancient phono console , then feeded to TQWT boxed RCA LC1B ;that tiny amp is somewhere around 1,5W/4E , so with RCA 16 ohms power is slightly (hehe) lower
when I find time to put in use some of my proper toob amps,along with any of toob preamp,I'll put back PD8500 in "xformer right after DAC output" mode again.....
all that in my workshop ( ya see the mess?) ;
this days I'm finishing major refurbishing of wife's house ( as I'm used to call it 😉 ) , so I'll finish Mau12 horn boxes for my 8" Sonido full rangers - for living room ...... dunno what will drive them,mebbe I'll finally finish my own Babelfish , in pure SE mode...... with disconnected output CCS modulation....
did I fed your curiosity enough?
btw- do not worry when I'll receive "my" Beta15s......... I have enough xperience with that range of Eminence drivers ;I didn't advise you blindly , looking just at graphs......
Attachments
Vix said:
Aghh....
Dunno who's that, but I prolonged my project a little...
There's a guy that was supposed to cut those baffles for me, and then he said.."sorry, I can't cut at such an angle !!" (side wings-look at Visaton No box project)
Then, the lack of out-of-job-free-time prevented me from lookin' for another carpenter. Hopefully it will be this weekend...
Vix
naah.......... if you have any free time........ just listen the music......
you have now everything needed ....... few days earlier or later - doesn't really matter
Zen Mod said:
Hehe.. Thanks for your reply.. Very nice setup you have there.. No babbelfish?.. I'm suprised.. 😉 I know you love the toobz..
I completly trust you on your recomendations after I listened to the babbelfish.. 🙂
I recived the Calligraphy tips today 😀😀 ..Maybe this weekend..
Vix said:Seems like a lot of OB related work is anticipated this weekend...😀
naah..........
not at my place, gents ......
tomorrow I'll receive first (little ) batch of
main pcbs....... I must populate few and send for Burnin' ......
Well ,looks like i got infected with OB disease 2.I really like what i have heard about them,and i really don't know what to expect from them.I am planning to run them with Trends 10.1.Will it be an problem?
They are so easy to made ,and sound quality/price ratio is unreal!(atl least i got that picture 😀).
Hope i'll have my baffles mounted till end of this month !
Best regards for people who came up with this idea ,and share it to the rest of the world !!!
(sorry 4 my terrible english 🙁 .This is my first post so plz be gentle on me
)
They are so easy to made ,and sound quality/price ratio is unreal!(atl least i got that picture 😀).
Hope i'll have my baffles mounted till end of this month !
Best regards for people who came up with this idea ,and share it to the rest of the world !!!
(sorry 4 my terrible english 🙁 .This is my first post so plz be gentle on me
)
chakija said:.....................This is my first post so plz be gentle on me
welcome
at least - you are allowed to post
TNX 😉
I asked you about using selenium st325 instead of APT ,but would like to know if someone else felt the same difference u did ,with this two phenolic driver.Difference in price is just 2 euro ,but if is a sound difference same as price one ,i would not want to spoil "all eminence" concept
I asked you about using selenium st325 instead of APT ,but would like to know if someone else felt the same difference u did ,with this two phenolic driver.Difference in price is just 2 euro ,but if is a sound difference same as price one ,i would not want to spoil "all eminence" concept
chakija said:TNX 😉
I asked you about using selenium st325 instead of APT ,but would like to know if someone else felt the same difference u did ,with this two phenolic driver.Difference in price is just 2 euro ,but if is a sound difference same as price one ,i would not want to spoil "all eminence" concept
go for Sel , anyway ...........
EnABl day....
Today got enough courage to try apply some paint on my drivers..
I did 2 sets of old car speakers before I applyed anything to the Alpha-6..
I have only done one driver, which is drying as I type this..
Today got enough courage to try apply some paint on my drivers..
I did 2 sets of old car speakers before I applyed anything to the Alpha-6..
I have only done one driver, which is drying as I type this..
An externally hosted image should be here but it was not working when we last tested it.
An externally hosted image should be here but it was not working when we last tested it.
Nice! So you'll listen to untreated and treated driver to hear difference? Did you treat the dustcap?
hakunin said:
Yes.. I'm quite familiar with the "All Eminence OB" in stock condition by now..
I did treat both drivers with the EnABl patterns and have them hooked up now.. I did listen to them a little bit today but there's been people here all day.. So it's to early to talk about sonic differences.. I have not applied any micro gloss clear coat yet.. maybe tomorrow.. 🙂
Yunick said:
give us picture or two of entire cone , so I will ask Bud to take a look and write few words
- Status
- Not open for further replies.