New Markaudio Drivers

[sdsddsd1]

Just went to the MA site to look up this voigt pipe for Pluvia 7HD.
https://www.kjfaudio.com/wp-content/uploads/2020/06/Pluvia-7HD-ML-Voigt.png

They have a new 200mm driver listet, MA200-M.
https://www.markaudio.com/online_shop/20-cm/ma200-m-multi-midnight-copper/

 

[GM]

At a glance looks like it could be scaled for the 7PHD.

 

[Scottmoose]

Ah, Thomas has got the MA200 up on the site. An interesting unit. I need to get the floorstander sketches / plans finished off so he can upload them to join the standmounts (a couple of others too); unfortunately I've been down with the dreaded lurgy for the past few days so not been able to get them to him yet. Hopefully next 48hrs.

 

[vinylkid58]

They have a new 200mm driver listet, MA200-M.

I suspected there was a larger driver coming. Pretty cool.

jeff

 

[Mitch311]

I wonder if it'll end up being used more as a woofer / mid-bass.
Seems to get a great response from a vented alignment and very smooth & efficient up to 3-4k hz.

 

[zman01]

Good to.see the new addition to the Mark Audio wide-band driver family.

 

[rock12]

Will the pluvia hd voight pipe work for the pluvia PHD

 

[Bryguy]

Those MA200's are very attractive

 

[LeifB60]

It will be interesting to see the price of the MA200-M.

 

[wchang]

My current expat/poor man's Monitor Audio 2.5-way uses Mo's RST-CCAM 8" woofers (Ceramic-Coated Al Mg) to support the Studio 2 with port plugged. Hopefully the MA200-M will be at least as good.

 

[Vermouth]

I have a pair of the new pluvia7PHD drivers and looking for a voight pipe type design

KJF have a few plans on there site, otherwise @Scottmoose can probably point you in the right direction.

 

[Scottmoose]

Still fighting off the dreaded lurgy, but it'll go straight into the 7HD design, no changes necessary. That doesn't automatically carry over for others, but it's an acoustically large enclosure so swamps out the modest variations in load requirements you'd get with acoustically smaller / more highly forced loads.

 

[Charles G]

I saw in the other 'Selecting a MA driver' thread that dave mentioned the 10M/P and eventually likely 12P were getting harder to find. Are any of the newer drivers going to have the right parameters for the large rear horns, or would it be a good idea to snag some while I can? (e.g. for the Silbury or Avebury)

Open to any general suggestions on paper vs metal for the 10, though I don't want to hijack the thread too much.

 

[Vermouth]

any indication on pricing on the new MA200’s? They look great.

 

[Mitch311]

$299 AUD ea apparently.

 

[Scottmoose]

I saw in the other 'Selecting a MA driver' thread that dave mentioned the 10M/P and eventually likely 12P were getting harder to find. Are any of the newer drivers going to have the right parameters for the large rear horns,

They all have; they're just a little different in requirements. All my Woden horns are current for e.g., we just haven't been able to update the site to reflect that. So don't worry about whether they can be used -they can. 😉

 

[tamra]

Glass cone looks interesting.
Maop11ms might be good too.
http://blog.fidelitatem-sound.jp/2024/07/03/コイズミ無線でのイベントを終えて/

 

[Ixnay]

Saw something like these in the Voice Coil mag. Just to hear them would be great. Always interested in what the new stuff can/cannot do.

 

[Squeak]

Glass cone looks interesting.
Maop11ms might be good too.
http://blog.fidelitatem-sound.jp/2024/07/03/コイズミ無線でのイベントを終えて/

Has this ever been done before?

 

[tamra]

Yes,they does often.